IDES Prospector Already have an account? Login Here

IDES

Ultrason® E 1010 NAT

Polyethersulfone

Supplied by BASF Corporation

The technical datasheet with complete property values for Ultrason® E 1010 NAT is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Unreinforced, low viscosity injection moulding grade, flows very readily.
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Agency Ratings 
Forms 
  • Pellets
Processing Method 
  • Extrusion
  • Injection Molding
  
Resin ID (ISO 1043)
  • PESU
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Apparent Density
g/cm³
 ISO 60
Melt Volume-Flow Rate (MVR) (360°C/10.0 kg)
in³/10min
 ISO 1133
Molding Shrinkage     ISO 294-4
Across Flow
%
  
Flow
%
  
Water Absorption     ISO 62
73°F, 24 hr
%
  
Equilibrium, 73°F, 50% RH
%
  
Viscosity Number
cm³/g
 ISO 307
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus (73°F)
psi
 ISO 527-2
Tensile Stress (Yield, 73°F)
psi
 ISO 527-2/50
Tensile Strain (Yield, 73°F)
%
 ISO 527-2/50
Tensile Creep Modulus (1000 hr)
psi
 ISO 899-1
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength     ISO 179/1eA
-22°F
ft·lb/in²
  
73°F
ft·lb/in²
  
Charpy Unnotched Impact Strength     ISO 179/1eU
-22°F
 
  
73°F
 
  
Notched Izod Impact Strength     ISO 180/1A
-22°F
ft·lb/in²
  
73°F
ft·lb/in²
  
Hardness
Nominal Value
Unit
Test Method
Ball Indentation Hardness (H 358/30)
psi
 ISO 2039-1
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature (264 psi, Unannealed)
°F
 ISO 75-2/A
CLTE - Flow      
73 to 176°F
in/in/°F
 ISO 11359-2
356°F
in/in/°F
 DIN 53752
Maximum Service Temperature 2
°F
 IEC 60216
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity
ohms
 IEC 60093
Volume Resistivity
ohm·cm
 IEC 60093
Relative Permittivity     IEC 60250
73°F, 100 Hz
 
  
73°F, 1 MHz
 
  
Dissipation Factor     IEC 60250
73°F, 100 Hz
 
  
73°F, 1 MHz
 
  
Comparative Tracking Index     IEC 60112
Solution A
V
  
Solution B
V
  
Electric Strength 3
V/mil
 IEC 60243-1
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL     UL 94
0.0630 in
 
  
0.125 in
 
  
Optical
Nominal Value
Unit
Test Method
Refractive Index
 
 ISO 489
Transmittance (78.7 mil)
%
 DIN 5036-3
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Ultrason® E 1010 NAT, Ultrason E 1010 NAT, Ultrason® E , Ultrason E, UltrasonE1010NAT, UltrasonE, E 1010 NAT, E1010 NAT, E1010, E1010NAT, 1010 NAT, 1010NAT, Polyethersulfone, PESU, Polysulfone, PSU, BASF, NAT1010, 1010E
Agency Ratings
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): EC (1).
Injection
Nominal Value
Unit
 
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Extrusion
Nominal Value
Unit
 
Melt Temperature
°F
  
Notes
1Typical properties: these are not to be construed as specifications.
2Short Cycle Operation
3K20/K20
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.