IDES Prospector Already have an account? Login Here

IDES

MACOMASS TPE MM-TPE-V 5031, R1690

Thermoplastic Elastomer

Supplied by MACOMASS Verkaufs AG

The technical datasheet with complete property values for MACOMASS TPE MM-TPE-V 5031, R1690 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Additive 
  • UV Stabilizer
Features 
  • Good Chemical Resistance
  • Good UV Resistance
  
Appearance 
  • Black
Forms 
  • Pellets
Processing Method 
  • Extrusion
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Elastomers
Nominal Value
Unit
Test Method
Tensile Stress (Yield)
psi
 ISO 37
Tensile Elongation (Break)
%
 ISO 37
Tear Strength
lbf/in
 ISO 34-1
Compression Set
%
 ISO 815
Hardness
Nominal Value
Unit
Test Method
Shore Hardness (Shore A, 15 sec)
 
 ISO 868
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: MACOMASS TPE MM-TPE-V 5031, R1690, MACOMASS TPE MMTPEV 5031 R1690, MACOMASS TPE , MACOMASSTPEMMTPEV5031R1690, MACOMASSTPE, TPEMM TPE V 5031 R 1690, MM, TPEMM-TPE-V 5031, R1690, TPEMMTPEV 5031 R1690, TPEMM:TPE:V 5031, R1690, TPEMM/TPE/V 5031, R1690, TPEMM+TPE+V 5031, R1690, TPEMM_TPE_V 5031, R1690, TPEMM TPE V 5031, R1690, TPEMMTPE, MM TPE V 5031 R 1690, TPEMMTPEV5031R1690, TPEMM_TPE_V 5031 R1690, TPEMM TPE V 5031 R1690, MM-TPE-V 5031, R1690, MMTPEV 5031 R1690, MM:TPE:V 5031, R1690, MM/TPE/V 5031, R1690, MM+TPE+V 5031, R1690, MM_TPE_V 5031, R1690, MM TPE V 5031, R1690, MMTPE, TPEV, V5031, 5031R, R1690, TPEMM_TPE_V5031R1690, MMTPEV5031R1690, MM_TPE_V 5031 R1690, MM TPE V 5031 R1690, MM_TPE_V5031R1690, Thermoplastic Elastomer, TPE, MACOMASS, ThermoplasticElastomer, TPEMM, TPETPEMM
Features
Features may also be described by the following terms: Good UV Resistance, UV Resistant, Ultraviolet Resistant, Ultraviolet Light Resistant, Good Chemical Resistance, Chemical Resistant.
Extrusion
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Melt Temperature
°F
  
Extrusion Notes
Compression ratio: 1:2.5 to 1:3
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.