IDES Prospector Already have an account? Login Here

IDES

TABOREX TA 1133 HD

High Density Polyethylene

Supplied by SILON s.ro

The technical datasheet with complete property values for TABOREX TA 1133 HD is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
A chemically-crosslinkable HDPE compound for the production of single and multi-layer pipes for domestic hot and cold water, under floor heating and central heating application.

TABOREX TA 1132 HD is a crosslinkable compound made by Silane grafted ethylene polymer. This graft polymer constitutes together with a Masterbatch containing the crosslinking catalyst a "SIOPLAS-SYSTEM". Pipes which are produced with the SILON grade TABOREX TA 1132 HD fulfil the requirements of ASTM F876-04a, CSA 137.5-03, EN ISO 15875, BS 7291 and all related standards.

This system allows the compound to be extruded as a normal thermoplastic polymer and will attain a high level of crosslinking in the processed form. The final product provides all the superior properties associated with crosslinked polyethylene.
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
  • Asia Pacific
  • Europe
  • Latin America
  • North America
  • South America
Features 
  • Crosslinkable
Uses 
  • Piping
Forms 
  • Spheres
Processing Method 
  • Extrusion
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 DIN 53479, ASTM D1505
Apparent Density
g/cm³
 DIN 53466
Melt Mass-Flow Rate (MFR) 2
     Internal Method
190°C/2.16 kg
g/10 min
  
190°C/5.0 kg
g/10 min
  
Gel Content
%
 EN 579
Moisture Content 3
%
 Internal Method
Volatile Matter 4
%
 Internal Method
Mechanical
Nominal Value
Unit
Test Method
Tensile Stress (Break)
psi
 ISO 527-2
Tensile Strain (Break)
%
 ISO 527-2
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: TABOREX TA 1133 HD, TABOREX , TABOREXTA1133HD, TA 1133 HD, TA1133, 1133HD, TA1133HD, Polyethylene, High Density, Polyethylene High Density, HDPE, Polyethylene, PE, SILON, PolyethyleneHighDensity, 1133TA
Uses
Uses may also be described by the following terms: Piping, Pipe.
Extrusion
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Cylinder Zone 1 Temp.
°F
  
Cylinder Zone 2 Temp.
°F
  
Cylinder Zone 3 Temp.
°F
  
Cylinder Zone 4 Temp.
°F
  
Die Temperature
°F
  
Extrusion Notes
L/D: >25
Compression ratio: 3:1 to 2.5 : 1
Head: 200 to 210°C
Screw: 70°C to 90 °C
Notes
1Typical properties: these are not to be construed as specifications.
2CON 2.2
3CON 45.1
4CON 4.3
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.