IDES Prospector Already have an account? Login Here

IDES

Cellidor CP 3406-11

Cellulose Acetate Propionate

Supplied by Albis Plastic GmbH

The technical datasheet with complete property values for Cellidor CP 3406-11 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
  • Europe
  • North America
Additive 
  • Plasticizer (110000 ppm)
Features 
  • Good Flow
  • High Stiffness
  • High Strength
  • Renewable Resource Content
  
Uses 
  • Eyeglass Frames
  • Thin-walled Parts
  
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Melt Volume-Flow Rate (MVR) (210°C/2.16 kg)
in³/10min
 ISO 1133
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ISO 527-2
Tensile Stress (Yield)
psi
 ISO 527-2
Tensile Strain
     ISO 527-2
Yield
%
  
Break
%
  
Nominal Tensile Strain at Break
%
 ISO 527-2
Flexural Strength (3.5% Strain)
psi
 ISO 178
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength (73°F)
ft·lb/in²
 ISO 179/1eA
Charpy Unnotched Impact Strength (73°F)
 
 ISO 179/1eU
Hardness
Nominal Value
Unit
Test Method
Ball Indentation Hardness (H 132/30)
psi
 ISO 2039-1
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature (264 psi, Unannealed)
°F
 ISO 75-2/A
Vicat Softening Temperature
°F
 ISO 306/B
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity
ohms
 IEC 60093
Volume Resistivity
ohm·cm
 IEC 60093
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Cellidor CP 3406-11, Cellidor CP 340611, Cellidor , CellidorCP340611, CP 3406, CP 3406-11, CP 340611, CP 3406:11, CP 3406/11, CP 3406+11, CP 3406_11, CP 3406 11, CP3406, 340611, CP340611, CP3406_11, Cellulose Acetate Propionate, CAP, Cellulose Acetate, CA, Albis Euro, CelluloseAcetatePropionate, CelluloseAcetate, 3406CP
Features
Features may also be described by the following terms: Good Flow, High Stiffness, High Strength, Renewable Resources, From Renewable Resources, Renewable Resource Derived, Renewable Raw Materials, Renewable Resource Content.
Uses
Uses may also be described by the following terms: Eyeglass Frames, Glasses Frames, Thin-walled Parts, Thin Walled Parts, Thin-wall Parts, Thin wall Parts, Thinwall Parts.
Injection
Nominal Value
Unit
 
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.