IDES Prospector Already have an account? Login Here

IDES

Lanufene HDI-5005

High Density Polyethylene

Supplied by Ras Lanuf Oil & Gas Processing Company (RASCO)

The technical datasheet with complete property values for Lanufene HDI-5005 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
LANUFENE HDI 5005 is a high density polyethylene resin intended for use primarily in injection molding and silane PEX pipes applications. LANUFENE HDI 5005 combines excellent stress cracking resistance (ESCR) and impact strength with low warpage, excellent gloss and good moldability.

LANUFENE HDI 5005 is recommended for injection molding applications - trash box, toys, industrial parts, and shoulder of laminated tube for toothpaste where good ESCR and impact strength are needed.
LANUFENE HDI 5005 can be also used for good base resin of silane XLPE (PEX) pipes application such as hot water and floor - heating pipes, portable water pipes and sanitary pipes.
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
  • Europe
  
Features 
  • Food Contact Acceptable
  • Good Impact Resistance
  • Good Moldability
  • High ESCR (Stress Crack Resist.)
  • High Gloss
  • Low Warpage
Uses 
  • Consumer Applications
  • Containers
  • Piping
  • Toys
  
Forms 
  • Pellets
Processing Method 
  • Injection Molding
  • Pipe Extrusion
  
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ASTM D1505
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)
g/10 min
 ASTM D1238
Environmental Stress-Cracking Resistance (F50)
hr
 ASTM D1693
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength (Ultimate)
psi
 ASTM D638
Tensile Elongation (Break)
%
 ASTM D638
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact
ft·lb/in
 ASTM D256A
Thermal
Nominal Value
Unit
Test Method
Brittleness Temperature
°F
 ASTM D746
Vicat Softening Temperature
°F
 ASTM D1525
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Lanufene HDI-5005, Lanufene HDI5005, Lanufene , LanufeneHDI5005, HDI, HDI-5005, HDI5005, HDI:5005, HDI/5005, HDI+5005, HDI_5005, HDI 5005, Polyethylene, High Density, Polyethylene High Density, HDPE, Polyethylene, PE, RASCO, PolyethyleneHighDensity, 5005HDI
Features
Features may also be described by the following terms: High Environmental Stress Cracking Resistance, High ESCR, Stress Cracking Resistant, High Gloss, Good Impact Resistance, Low Warpage, Low Warp, Good Moldability.
Uses
Uses may also be described by the following terms: Piping, Pipe.
Injection
Nominal Value
Unit
 
Processing (Melt) Temp
°F
  
Extrusion
Nominal Value
Unit
 
Melt Temperature
°F
  
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.