IDES Prospector Already have an account? Login Here

IDES

AKROMID® B3

Polyamide 6

Supplied by AKRO-PLASTIC GmbH

The technical datasheet with complete property values for AKROMID® B3 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
This material, produced by AKRO-PLASTICS in China, has identical property data and carries this grade designationn: B3 CN (2500) (Dry)
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
  • Europe
  
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Dry
Conditioned
Unit
Test Method
Density
--
g/cm³
 ISO 1183
Molding Shrinkage
       ISO 294-4
Across Flow
--
%
  
Flow
--
%
  
Water Absorption
       ISO 62
Saturation, 73°F
--
%
  
Equilibrium, 73°F, 50% RH
--
%
  
Mechanical
Dry
Conditioned
Unit
Test Method
Tensile Modulus
psi
 ISO 527-2/1
Tensile Stress (Yield)
psi
 ISO 527-2/50
Tensile Strain (Break)
%
 ISO 527-2/50
Impact
Dry
Conditioned
Unit
Test Method
Charpy Notched Impact Strength
       ISO 179/1eA
-22°F
--
ft·lb/in²
  
73°F
ft·lb/in²
  
Charpy Unnotched Impact Strength
       ISO 179/1eU
-22°F
--
 
  
73°F
 
  
Thermal
Dry
Conditioned
Unit
Test Method
Heat Deflection Temperature
        
66 psi, Unannealed
--
°F
 ISO 75-2/B
264 psi, Unannealed
--
°F
 ISO 75-2/A
Melting Temperature
--
°F
 ISO 11357-3
Temperature Index
       IEC 216
-- 2
--
°F
  
-- 3
--
°F
  
Electrical
Dry
Conditioned
Unit
Test Method
Surface Resistivity
ohms
 IEC 60093
Volume Resistivity
ohm·cm
 IEC 60093
Comparative Tracking Index (Solution A)
--
V
 IEC 60112
Flammability
Dry
Conditioned
Unit
Test Method
Burning Rate 4 (0.0394 in)
--
in/min
 FMVSS 302
Flame Rating - UL (0.0630 in)
--
 
 UL 94
Additional Information
Dry
Conditioned
Unit
Test Method
Flowability - Flowspiral 5
--
in
 Internal Method
Related Terminology
Dry
Product names can be difficult to match. You may have searched any one of these terms to find this product: AKROMID® B3, AKROMID B3, AKROMID® , AKROMID, AKROMIDB3, B 3, B3, Polyamide 6, Nylon 6, Polyamide, Nylon, pa6, AKRO-PLASTIC, Polyamide6, Nylon6, 3B
Generic Name
Dry
Generic Name may also be described by the following terms: PA6.
Conditioned
Product names can be difficult to match. You may have searched any one of these terms to find this product: AKROMID® B3, AKROMID B3, AKROMID® , AKROMID, AKROMIDB3, B 3, B3, Polyamide 6, Nylon 6, Polyamide, Nylon, pa6, AKRO-PLASTIC, Polyamide6, Nylon6, 3B

Generic Name may also be described by the following terms: PA6.
Injection
Dry
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Nozzle Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Injection Pressure
psi
  
Holding Pressure
psi
  
Back Pressure
psi
  
Injection Notes
Feed Section: 60 to 80°C
Notes
1Typical properties: these are not to be construed as specifications.
250 % loss of tens.strength, 5000 hrs
350 % loss of tens.strength, 20000 hrs
4Passed
5mould temperature: 80 °C, melt temperature: 270 °C, injection pressure: 750 bar, cross section of flow spiral: 7 mm x 3.5 mm
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.