IDES Prospector Already have an account? Login Here

IDES

Versollan™ RU 2204X

Thermoplastic Elastomer

Supplied by GLS Thermoplastic Elastomers

The technical datasheet with complete property values for Versollan™ RU 2204X is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Versollan™ RU 2204X is the first of a new class of high performance, injection moldable TPU alloys developed to offer a rubbery feel and appearance, reduced cycle times, combined with the performance properties associated with TPUs.
  • Bonds to PC, ABS, PC/ABS, and Copolyester
  • Excellent Abrasion Resistance
  • Fast Set Up Rates During Processing
  • Good Chemical and Oil Resistance
  • Matte Finish
  • Rubbery, Soft Touch Feel
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
  • Asia Pacific
  • Europe
  • North America
  • South America
Features 
  • Good Abrasion Resistance
  • Good Chemical Resistance
  • Oil Resistant
Appearance 
  • Natural Color
Processing Method 
  • Extrusion
  • Injection Molding
  
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Melt Mass-Flow Rate (MFR)
     ASTM D1238
190°C/2.16 kg
g/10 min
  
200°C/5.0 kg
g/10 min
  
Molding Shrinkage - Flow
in/in
 ASTM D955
Elastomers
Nominal Value
Unit
Test Method
Tensile Stress 2, 3
     ASTM D412
100% Strain, 73°F
psi
  
300% Strain, 73°F
psi
  
Tensile Strength 2, 3 (Break, 73°F)
psi
 ASTM D412
Tensile Elongation 2, 3 (Break, 73°F)
%
 ASTM D412
Tear Strength
lbf/in
 ASTM D624
Compression Set (73°F, 22.0 hr)
%
 ASTM D395B
Hardness
Nominal Value
Unit
Test Method
Durometer Hardness (Shore A, 10 sec)
 
 ASTM D2240
Fill Analysis
Nominal Value
Unit
Test Method
Apparent Viscosity
     ASTM D3835
392°F, 1340 sec^-1
Pa·s
  
392°F, 11200 sec^-1
Pa·s
  
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Versollan™ RU 2204X, Versollan RU 2204X, Versollan™ , Versollan, VersollanRU2204X, RU 2204 X, RU 2204X, RU2204, 2204X, RU2204X, Thermoplastic Elastomer, TPE, GLS, ThermoplasticElastomer, 2204RU
Features
Features may also be described by the following terms: Good Chemical Resistance, Chemical Resistant, Good Abrasion Resistance, Abrasion Resistant.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Suggested Max Moisture
%
  
Suggested Max Regrind
%
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Nozzle Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Back Pressure
psi
  
Screw Speed
rpm
  
Injection Notes
Color concentrates with EVA or LDPE carrier are most suitable for coloring Versollan™ RU 2204X. Typical letdown ratios are 50:1 to 25:1 - loading levels should be as low as possible to minimize the effect on adhesion. A high color match consistency can be obtained by the use of precolored compounds available from GLS. Concentrates based on PVC should not be used. The final determination of color concentrate suitability should be determined by customer trials.

Purge thoroughly before and after use of this product with a low flow (0.5 - 2.5 MFR) polyethylene (PE) or polypropylene (PP).

Regrind levels up to 20% can be used with Versollan™ RU 2204X with minimal property loss, provided that the regrind is free of contamination. To minimize losses during molding, the melt temperature should remain as low as possible. The final determination of regrind effectiveness should be determined by the customer.

Versollan™ RU 2204X should not be left in the barrel for extended idle periods (greater than 5 minutes).

Suggested Dewpoint: -40°F

Injection Speed: 0.5 to 2 in/sec
1st Stage - Boost Pressure: 300 to 700 psi
2nd Stage - Hold Pressure: 30% of Boost
Hold Time (Thick Part): 4 to 10 sec
Hold Time (Thin Part): 1 to 3 sec
Notes
1Typical properties: these are not to be construed as specifications.
2Die C
32 hr
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.