IDES Prospector Already have an account? Login Here

IDES

Di-PAK E-4501

Thermoplastic

Supplied by Hapco Inc.

The technical datasheet with complete property values for Di-PAK E-4501 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
DI-PAK E-4701, E-4951 and E-4501
Easily pourable, thermally conductive, shock resistant potting compounds that are ideally suited for low and high production applications. This series of DI-PAK products reduce rejects by exhibiting extremely low stress on potted components. All three of the above DI-PAK E products are flame retardant and meet UL 94V-0 requirements.
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Features 
  • Electrically Insulating
  • Fast Cure
  • Flame Retardant
  • Good Flexibility
  • Low to No Water Absorption
  • Low Viscosity
  • Shock Absorbent
  • Thermally Conductive
Uses 
  • Battery Cases
  • Electrical/Electronic Applications
  • Power Cable Shields
  • Switches
  
Appearance 
  • Black
Forms 
  • Liquid
Processing Method 
  • Potting
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D4669
Molding Shrinkage - Flow
in/in
 ASTM D2566
Weight - per cubic inch
g
  
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ASTM D638
Tensile Strength
psi
 ASTM D638
Tensile Elongation (Break)
%
 ASTM D638
Flexural Modulus
psi
 ASTM D790
Flexural Strength
psi
 ASTM D790
Elastomers
Nominal Value
Unit
Test Method
Tear Strength 2
lbf/in
 ASTM D624
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact
ft·lb/in
 ASTM D256
Unnotched Izod Impact
 
 ASTM D256
Hardness
Nominal Value
Unit
Test Method
Durometer Hardness (Shore D)
 
 ASTM D2240
Thermal
Nominal Value
Unit
Test Method
CLTE - Flow
in/in/°F
 ASTM D696
Thermal Conductivity
Btu·in/hr/ft²/°F
  
Service Temperature
°F
  
Electrical
Nominal Value
Unit
Test Method
Volume Resistivity
ohm·cm
 ASTM D257
Dielectric Strength
V/mil
 ASTM D149
Dielectric Constant
     ASTM D150
1 kHz
 
  
100 kHz
 
  
Dissipation Factor (77°F, 100 kHz)
 
 ASTM D150
Thermoset
Nominal Value
Unit
Test Method
Thermoset Components
      
Part A
 
  
Part B
 
  
Thermoset Mix Viscosity (77°F)
cP
 ASTM D4878
Demold Time (70°F)
min
  
Gel Time 3 (77°F)
min
 ASTM D2971
Additional Information
Nominal Value
Unit
Test Method
Thermal Shock Test
 
  
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Di-PAK E-4501, DiPAK E4501, Di-PAK , DiPAK, Di:PAK, Di/PAK, Di+PAK, Di_PAK, Di PAK, DiPAKE4501, E-4501, E4501, E:4501, E/4501, E+4501, E_4501, E 4501, Thermoplastic, Unspecified, Thermoplastic Unspecified, TP, Unspecified, TP Unspecified, Hapco Inc., ThermoplasticUnspecified, TPUnspecified, 4501E
Features
Features may also be described by the following terms: Low Viscosity, Fast Cure, Fast Curing, Good Flexibility, Flexible, Low Water Absorption, Low Moisture Absorption, Water Resistant, Moisure Resistant.
Uses
Uses may also be described by the following terms: Electrical Applications, Electronic Applications, Electrical/Electronic Applications, Electrical Sector.
Notes
1Typical properties: these are not to be construed as specifications.
2Die C
3100 g
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.