IDES Prospector Already have an account? Login Here

IDES

Quattor® BF-22020 S3

Linear Low Density Polyethylene

Supplied by Quattor Petroquímica

The technical datasheet with complete property values for Quattor® BF-22020 S3 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Quattor® BF-22020 S3 is a linear low density polyethylene, butene copolymer, produced through Unipol® process and recommended for blown film extrusion.
Films produced using Quattor® BF-22020 S3 have good processability, better mechanical performance in comparison to
conventional low density polyethylene (LDPE) and are easily welded even at high speed packaging machines.

Applications: automatic packaging (FFS), general purpose, blends with HDPE and LDPE and lamination.
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
  • South America
  
Additive 
  • Antiblock
  • Slip
  
Features 
  • Antiblocking
  • Butene Comonomer
  • Good Processability
  • Slip
  • Weldable
Uses 
  • Blending
  • Film
  • Laminates
  • Packaging
  
Processing Method 
  • Blown Film
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ASTM D1505
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)
g/10 min
 ASTM D1238
Mechanical
Nominal Value
Unit
Test Method
Coefficient of Friction (vs. Itself - Dynamic, Blown Film)
 
 ASTM D1894
Films
Nominal Value
Unit
Test Method
Film Thickness - Tested
mil
  
Tensile Strength
     ASTM D882
MD: Yield, 0.98 mil, Blown Film
psi
  
TD: Yield, 0.98 mil, Blown Film
psi
  
MD: Break, 0.98 mil, Blown Film
psi
  
TD: Break, 0.98 mil, Blown Film
psi
  
Tensile Elongation
     ASTM D882
MD: Yield, 0.98 mil, Blown Film
%
  
TD: Yield, 0.98 mil, Blown Film
%
  
MD: Break, 0.98 mil, Blown Film
%
  
TD: Break, 0.98 mil, Blown Film
%
  
Dart Drop Impact (0.98 mil, Blown Film)
g
 ASTM D1709A
Elmendorf Tear Strength
     ASTM D1922
MD: 0.98 mil, Blown Film
g
  
TD: 0.98 mil, Blown Film
g
  
Optical
Nominal Value
Unit
Test Method
Gloss (45°)
 
 ASTM D2457
Haze
%
 ASTM D1003
Additional Information
Film data obtained on 25 µm thickness film produced on a 75 mm extruder, blow up ratio 2.2:1, die gap 2.1 mm, and 120 kg/h output
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Quattor® BF-22020 S3, Quattor BF22020 S3, Quattor® , Quattor, QuattorBF22020S3, BF, BF 22020 S 3, BF-22020 S3, BF22020 S3, BF:22020 S3, BF/22020 S3, BF+22020 S3, BF_22020 S3, BF 22020 S3, BF22020, 22020S, S3, BF22020S3, BF_22020S3, Polyethylene, Linear Low Density, Polyethylene Linear Low Density, LLDPE, Polyethylene, PE, Quattor Petroquimica, PolyethyleneLinearLowDensity, 22020BF
Features
Features may also be described by the following terms: Good Processability, Easy Processing, Butene Comonomer, Antiblocking, Unspecified Antiblock, Slip, Unspecified Slip.
Extrusion
Nominal Value
Unit
 
Cylinder Zone 1 Temp.
°F
  
Cylinder Zone 2 Temp.
°F
  
Cylinder Zone 3 Temp.
°F
  
Cylinder Zone 4 Temp.
°F
  
Cylinder Zone 5 Temp.
°F
  
Melt Temperature
°F
  
Extrusion Notes
Blow-up Ratio: 2.0 to 3.0:1
Minimum Thickness: 15 microns per wall
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.