IDES Prospector Already have an account? Login Here

IDES

Quattor® HF-22008 S3

Linear Low Density Polyethylene

Supplied by Quattor Petroquímica

The technical datasheet with complete property values for Quattor® HF-22008 S3 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Quattor® HF-22008 S3 is a linear low density polyethylene, hexene copolymer, produced through Unipol® process and recommended for blown film extrusion blended with low density polyethylene (LDPE).
Films produced using Quattor® HF-22008 S3 have excellent mechanical properties, an outstanding gloss and good sealability even at high speed packaging machines

Applications: automatic packaging (FFS) for solids and liquids, frozen food packaging, lamination and coextrusion.
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
  • South America
  
Additive 
  • Antiblock
  • Processing Aid
  • Slip
Features 
  • Antiblocking
  • Good Heat Seal
  • Hexene Comonomer
  • High Gloss
  • Slip
Uses 
  • Film
  • Food Packaging
  • Laminates
  • Packaging
  
Processing Method 
  • Blown Film
  • Coextrusion
  
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ASTM D1505
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)
g/10 min
 ASTM D1238
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus - 1% Secant (Compression Molded)
psi
 ASTM D638
Tensile Strength
     ASTM D638
Yield, Compression Molded
psi
  
Break, Compression Molded
psi
  
Tensile Elongation
     ASTM D638
Yield, Compression Molded
%
  
Break, Compression Molded
%
  
Coefficient of Friction (vs. Itself - Dynamic, Blown Film)
 
 ASTM D1894
Films
Nominal Value
Unit
Test Method
Film Thickness - Tested
mil
  
Tensile Strength
     ASTM D882
MD: Yield, 0.98 mil, Blown Film
psi
  
TD: Yield, 0.98 mil, Blown Film
psi
  
MD: Break, 0.98 mil, Blown Film
psi
  
TD: Break, 0.98 mil, Blown Film
psi
  
Tensile Elongation
     ASTM D882
MD: Yield, 0.98 mil, Blown Film
%
  
TD: Yield, 0.98 mil, Blown Film
%
  
MD: Break, 0.98 mil, Blown Film
%
  
TD: Break, 0.98 mil, Blown Film
%
  
Dart Drop Impact (0.98 mil, Blown Film)
g
 ASTM D1709A
Elmendorf Tear Strength
     ASTM D1922
MD: 0.98 mil, Blown Film
g
  
TD: 0.98 mil, Blown Film
g
  
Hardness
Nominal Value
Unit
Test Method
Durometer Hardness (Shore D, Compression Molded)
 
 ASTM D2240
Thermal
Nominal Value
Unit
Test Method
Vicat Softening Temperature
°F
 ASTM D1525
Optical
Nominal Value
Unit
Test Method
Gloss (45°)
 
 ASTM D2457
Haze
%
 ASTM D1003
Additional Information
Film data obtained on 25 µm thickness film produced on a 70 mm extruder, blow up ratio 2.2:1, die gap 1.8 mm, and 120 kg/h output
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Quattor® HF-22008 S3, Quattor HF22008 S3, Quattor® , Quattor, QuattorHF22008S3, HF, HF 22008 S 3, HF-22008 S3, HF22008 S3, HF:22008 S3, HF/22008 S3, HF+22008 S3, HF_22008 S3, HF 22008 S3, HF22008, 22008S, S3, HF22008S3, HF_22008S3, Polyethylene, Linear Low Density, Polyethylene Linear Low Density, LLDPE, Polyethylene, PE, Quattor Petroquimica, PolyethyleneLinearLowDensity, 22008HF
Features
Features may also be described by the following terms: Hexene Comonomer, High Gloss, Good Heat Seal, Antiblocking, Unspecified Antiblock, Slip, Unspecified Slip.
Uses
Uses may also be described by the following terms: Food Packaging.
Extrusion
Nominal Value
Unit
 
Cylinder Zone 1 Temp.
°F
  
Cylinder Zone 2 Temp.
°F
  
Cylinder Zone 3 Temp.
°F
  
Cylinder Zone 4 Temp.
°F
  
Cylinder Zone 5 Temp.
°F
  
Melt Temperature
°F
  
Extrusion Notes
Blow-up Ratio: 2.0 to 3.0:1
Minimum Thickness: 20 microns per wall
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.