IDES Prospector Already have an account? Login Here

IDES

Tarflon® GZ2510

Polycarbonate

Glass Fabric Reinforcement, 10%

Supplied by Idemitsu Chemicals

The technical datasheet with complete property values for Tarflon® GZ2510 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Polycarbonate-10 % GF; Ignition Resistant; Low viscosity Spiral Flow Length 32cm; Mould release; Injection mouldig grade
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
  • Europe
  • North America
Filler / Reinforcement 
  • Glass Fabric Reinforcement, 10% Filler by Weight
Additive 
  • Flame Retardant
  • Mold Release
  
Features 
  • Flame Retardant
  • Good Mold Release
  • Low Viscosity
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Molding Shrinkage
     ASTM D955
Flow
in/in
  
Across Flow
in/in
  
Water Absorption (73°F, 24 hr)
%
 ISO 62
Spiral Flow Length 2
in
 Internal Method
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ISO 527-2
Tensile Stress
     ISO 527-2
Yield
psi
  
Break
psi
  
Nominal Tensile Strain at Break
%
 ISO 527-2
Flexural Modulus
psi
 ISO 178
Flexural Strength
psi
 ISO 178
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength (73°F)
ft·lb/in²
 ISO 179
Hardness
Nominal Value
Unit
Test Method
Rockwell Hardness (M-Scale)
 
 ISO 2039-2
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature (264 psi, Unannealed)
°F
 ISO 75-2/A
CLTE - Flow
in/in/°F
 ASTM D696
Electrical
Nominal Value
Unit
Test Method
Volume Resistivity
ohm·cm
 IEC 60093
Relative Permittivity
     IEC 60250
100 Hz
 
  
1 MHz
 
  
Dissipation Factor
     IEC 60250
100 Hz
 
  
1 MHz
 
  
Arc Resistance
sec
 ASTM D495
Electric Strength (0.0630 in)
V/mil
 IEC 60243-1
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL (0.0591 in)
 
 UL 94
Glow Wire Flammability Index
     IEC 60695-2-12
0.0394 in
°F
  
0.0591 in
°F
  
0.118 in
°F
  
Oxygen Index
%
 ASTM D2863
UL File Number
 
  
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Tarflon® GZ2510 , Tarflon GZ2510, Tarflon® , Tarflon, TarflonGZ2510, GZ 2510, GZ2510, Polycarbonate, PC, Idemitsu, 2510GZ
Features
Features may also be described by the following terms: Low Viscosity, Good Mold Release, Easy Release, Good Demolding.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Notes
1Typical properties: these are not to be construed as specifications.
2injection pressure : 110 MPa, thickness : 3 mm, width : 10 mm,
mold temperature : 80°C, cylinder temperature : 300°C
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.