IDES Prospector Already have an account? Login Here

IDES

Halene L 71501S

Linear Low Density Polyethylene

Supplied by Haldia Petrochemicals Ltd.

The technical datasheet with complete property values for Halene L 71501S is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
71501S is a LLDPE blown film grade produced by the Spherilene Technology.

This grade can be used in General Purpose Packaging Film Applications.

71501S is additivated with slip and antiblocking additives for excellent openability and slip properties.
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
Additive 
  • Antiblock
  • Slip
  
Features 
  • Antiblocking
  • Slip
  
Uses 
  • Film
  • Packaging
  
Processing Method 
  • Blown Film
Physical
Nominal Value
Unit
Test Method
Density 2
g/cm³
 ASTM D1505
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)
g/10 min
 ASTM D1238
Films
Nominal Value
Unit
Test Method
Film Thickness - Tested
mil
  
Tensile Strength 3
     ASTM D882
MD: Yield, 0.98 mil, Blown Film
psi
  
TD: Yield, 0.98 mil, Blown Film
psi
  
MD: Break, 0.98 mil, Blown Film
psi
  
TD: Break, 0.98 mil, Blown Film
psi
  
Tensile Elongation 3
     ASTM D882
MD: Break, 0.98 mil, Blown Film
%
  
TD: Break, 0.98 mil, Blown Film
%
  
Dart Drop Impact 4 (0.98 mil, Blown Film)
g
 ASTM D1709A
Elmendorf Tear Strength
     ASTM D1922
MD: 0.98 mil, Blown Film
g
  
TD: 0.98 mil, Blown Film
g
  
Optical
Nominal Value
Unit
Test Method
Gloss (60°, 0.984 mil, Blown Film)
 
 ASTM D2457
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Halene L 71501S, Halene L , HaleneL71501S, HaleneL, L 71501 S, L71501S, L71501, 71501 S, 71501S, Polyethylene, Linear Low Density, Polyethylene Linear Low Density, LLDPE, Polyethylene, PE, Haldia Petrochem, PolyethyleneLinearLowDensity, S71501, 71501L
Features
Features may also be described by the following terms: Antiblocking, Unspecified Antiblock, Slip, Unspecified Slip.
Extrusion
Nominal Value
Unit
 
Cylinder Zone 1 Temp.
°F
  
Cylinder Zone 2 Temp.
°F
  
Cylinder Zone 3 Temp.
°F
  
Cylinder Zone 4 Temp.
°F
  
Cylinder Zone 5 Temp.
°F
  
Melt Temperature
°F
  
Extrusion Notes
Blow up Ratio: 2.0 to 3.0
Die Gap: 2.0 to 2.5 mm
Notes
1Typical properties: these are not to be construed as specifications.
223°C
320 in/min
438 mm Dart, 66 cm Height
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.