IDES Prospector Already have an account? Login Here

IDES

Di-PAK R-4545/40

Thermoplastic

Supplied by Hapco Inc.

The technical datasheet with complete property values for Di-PAK R-4545/40 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
RIGID

DI-PAK R-4545 Series
A very low viscosity potting and encapsulating system with excellent flow and penetration into the most intricate electronic components, without voids or porosity. The R-4545 Series cure to a hard, shiny, high gloss, plastic finish that is free from "blushing" under all humidity conditions. The R-4545 Series is ideal for electrical applications where surface finish and appearance are critical.
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Features 
  • Blush Resistant
  • Electrically Insulating
  • Good Processability
  • Good Toughness
  • High Flow
  • High Gloss
  • High Heat Resistance
  • Low Viscosity
  • Pleasing Surface Appearance
Uses 
  • Battery Cases
  • Electrical/Electronic Applications
  • Power Cable Shields
  • Switches
  
Appearance 
  • Black
Forms 
  • Liquid
Processing Method 
  • Encapsulating
  • Potting
  
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D4669
Molding Shrinkage - Flow
in/in
 ASTM D2566
Weight - per cubic inch
g
  
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ASTM D638
Tensile Strength
psi
 ASTM D638
Tensile Elongation (Break)
%
 ASTM D638
Flexural Modulus
psi
 ASTM D790
Flexural Strength
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact
ft·lb/in
 ASTM D256
Unnotched Izod Impact
ft·lb/in
 ASTM D256
Hardness
Nominal Value
Unit
Test Method
Durometer Hardness (Shore D)
 
 ASTM D2240
Thermal
Nominal Value
Unit
Test Method
Thermal Conductivity
Btu·in/hr/ft²/°F
  
Service Temperature
°F
  
Electrical
Nominal Value
Unit
Test Method
Volume Resistivity
ohm·cm
 ASTM D257
Dielectric Strength
V/mil
 ASTM D149
Dielectric Constant
     ASTM D150
1 kHz
 
  
100 kHz
 
  
Dissipation Factor (77°F, 100 kHz)
 
 ASTM D150
Thermoset
Nominal Value
Unit
Test Method
Thermoset Components
      
Part A
 
  
Part B
 
  
Thermoset Mix Viscosity (77°F)
cP
 ASTM D4878
Demold Time (70°F)
min
  
Gel Time 2 (77°F)
min
 ASTM D2971
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Di-PAK R-4545/40, DiPAK R454540, Di-PAK , DiPAK, Di:PAK, Di/PAK, Di+PAK, Di_PAK, Di PAK, DiPAKR454540, R 4545 40, R-4545/40, R454540, R-4545:40, R-4545+40, R-4545-40, R-4545_40, R-4545 40, R:4545/40, R/4545/40, R+4545/40, R_4545/40, R 4545/40, R4545, 454540, R4545_40, R4545 40, R_454540, R 454540, Thermoplastic, Unspecified, Thermoplastic Unspecified, TP, Unspecified, TP Unspecified, Hapco Inc., ThermoplasticUnspecified, TPUnspecified, 4545R
Features
Features may also be described by the following terms: Good Processability, Easy Processing, Good Toughness, Tough, Pleasing Surface Appearance, High Gloss, High Flow, High Melt, High MFI, Blush Reistant, Low Viscosity, High Heat Resistance.
Uses
Uses may also be described by the following terms: Electrical Applications, Electronic Applications, Electrical/Electronic Applications, Electrical Sector.
Notes
1Typical properties: these are not to be construed as specifications.
2100 g
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.