IDES Prospector Already have an account? Login Here

IDES

Beetle® PBTS100T

Polybutylene Terephthalate

Supplied by Teknor Apex Company (Chem Polymer)

The technical datasheet with complete property values for Beetle® PBTS100T is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
PBTS100T is a unfilled, toughened general purpose grade of PBT offering a good balance of flow and impact performance making it ideal for injection moulding.
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
  • North America
  
Additive 
  • Impact Modifier
Features 
  • General Purpose
  • Good Flow
  • Good Impact Resistance
  • Good Toughness
  
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Molding Shrinkage 2
%
 Internal Method
Mechanical
Nominal Value
Unit
Test Method
Tensile Stress (Break)
psi
 ISO 527-2
Tensile Strain (Break)
%
 ISO 527-2
Flexural Modulus
psi
 ISO 178
Flexural Strength
psi
 ISO 178
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength
ft·lb/in²
 ISO 179
Notched Izod Impact Strength
ft·lb/in²
 ISO 180
Unnotched Izod Impact Strength
 
 ISO 180
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature
      
66 psi, Unannealed
°F
 ISO 75-2/B
264 psi, Unannealed
°F
 ISO 75-2/A
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity
ohms
 IEC 60093
Volume Resistivity
ohm·cm
 IEC 60093
Comparative Tracking Index
V
 IEC 60112
Electric Strength (0.118 in)
V/mil
 IEC 60243-1
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Beetle® PBTS100T, Beetle PBTS100T, Beetle® , Beetle, BeetlePBTS100T, PBTS 100 T, PBTS100T, PBTS100, 100T, Polybutylene Terephthalate, PBT, Polyester, Teknor Apex Chem Poly, PolybutyleneTerephthalate, 100PBTS
Features
Features may also be described by the following terms: Good Impact Resistance, Good Toughness, Tough, Good Flow.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Injection Rate
 
  
Screw Speed
rpm
  
Injection Notes
Back Pressure: Low
Injection Pressure: High
Notes
1Typical properties: these are not to be construed as specifications.
2Mould shrinkage is significantly influenced by many factors including wall thickness, gating, component shape and moulding conditions. The range values stated were determined from specimen bar mouldings of 1.5mm to 4mm wall thickness. They are provided as a guide for comparison purposes only and no guarantee should be inferred from their inclusion. (Specimens measured in the dry state, 24 hours after moulding).
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.