IDES Prospector Already have an account? Login Here

IDES

ATTANE™ NG 4703G

Ultra Low Density Polyethylene Resin

Supplied by The Dow Chemical Company

The technical datasheet with complete property values for ATTANE™ NG 4703G is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
ATTANE™ NG 4703 ULPDE resin is a Next Generation (NG), ultra-low density resin from Dow. The ATTANE™ resins that you know and love are now kicked up a notch for excellent toughness.

Features:
  • Great optics
  • Good cold temperature toughness
  • Great flex crack resistance
  • Low seal initiation temperature

Complies with:
  • Canadian HPFB No Objection (with limitations)
  • U.S. FDA FCN 424
Consult the regulations for complete details.
General  
Material Status 
  • Commercial: Active
Availability 
  • Latin America
  • North America
  
Additive 
  • Antiblock (3750 ppm)
  • Slip (1500 ppm)
  
Agency Ratings 
 
Forms 
  • Pellets
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)
g/10 min
 ASTM D1238
Films
Nominal Value
Unit
Test Method
Film Puncture Resistance (2.0 mil)
ft·lb/in³
 Internal Method
Secant Modulus
     ASTM D882
2% Secant, MD: 2.0 mil
psi
  
2% Secant, TD: 2.0 mil
psi
  
Tensile Strength
     ASTM D882
MD: Yield, 2.0 mil
psi
  
TD: Yield, 2.0 mil
psi
  
MD: Break, 2.0 mil
psi
  
TD: Break, 2.0 mil
psi
  
Tensile Elongation
     ASTM D882
MD: Break, 2.0 mil
%
  
TD: Break, 2.0 mil
%
  
Dart Drop Impact (2.0 mil)
g
 ASTM D1709
Elmendorf Tear Strength
     ASTM D1922
MD: 2.0 mil
g
  
TD: 2.0 mil
g
  
Optical
Nominal Value
Unit
Test Method
Gloss (45°, 2.00 mil)
 
 ASTM D2457
Haze (2.00 mil)
%
 ASTM D1003
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: ATTANE™ NG 4703G, ATTANE NG 4703G, ATTANE™ , ATTANE, ATTANENG4703G, NG 4703 G, NG 4703G, NG4703, 4703G, NG4703G, Polyethylene, Ultra Low Density, Polyethylene Ultra Low Density, ULDPE, Polyethylene, PE, Dow, PolyethyleneUltraLowDensity, 4703NG
Agency Ratings
This plastic material has 2 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): FDA (1), HPFB (Canada) (1).
Extrusion Notes
Fabrication Conditions For Blown Film:
  • Screw Size: 25 inch; 30:1 L/D
  • Screw Type: Simple with mixer
  • Die Gap: 70 mil (1.8 mm)
  • Melt Temperature: 467°F (242°C)
  • Output: 7.6 lb/hr/in. of die circumference
  • Die Diameter: 6 in.
  • Blow-Up Ratio: 2.5:1
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.