IDES Prospector Already have an account? Login Here

IDES

Badalac® ABS 10 TM-Z2

Acrylonitrile Butadiene Styrene

Supplied by Bada AG

The technical datasheet with complete property values for Badalac® ABS 10 TM-Z2 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
ABS-I
Super tough grade suitable for injection moulding and extrusion
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Features 
  • Ultra High Toughness
Processing Method 
  • Extrusion
  • Injection Molding
  
Physical
Nominal Value
Unit
Test Method
Density 2
g/cm³
 ISO 1183
Melt Volume-Flow Rate (MVR) (220°C/10.0 kg)
in³/10min
 ISO 1133
Water Absorption
     ISO 62
Saturation, 73°F
%
  
Equilibrium, 73°F, 50% RH
%
  
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus 3 (73°F)
psi
 ISO 527-2/1
Tensile Stress 3 (Yield, 73°F)
psi
 ISO 527-2/50
Tensile Strain 3 (Yield, 73°F)
%
 ISO 527-2/50
Nominal Tensile Strain at Break 3 (73°F)
%
 ISO 527-2/50
Flexural Strength 4 (73°F)
psi
 ISO 178
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength 4
     ISO 179/1eA
-22°F
ft·lb/in²
  
73°F
ft·lb/in²
  
Charpy Unnotched Impact Strength 4
     ISO 179/1eU
-22°F
ft·lb/in²
  
73°F
 
  
Notched Izod Impact Strength 4
      
-22°F
ft·lb/in²
 ISO 180
73°F
ft·lb/in²
 ISO 180/1A
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature 5
      
66 psi, Unannealed
°F
 ISO 75-2/B
264 psi, Unannealed
°F
 ISO 75-2/A
Vicat Softening Temperature 6
      
--
°F
 ISO 306/A50
--
°F
 ISO 306/B50
CLTE - Flow 7
in/in/°F
 DIN 53752
Maximum Service Temperature - 20000 hrs
°F
 IEC 216
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity 8
ohms
 IEC 60093
Volume Resistivity 8
ohm·cm
 IEC 60093
Relative Permittivity 8 (1 MHz)
 
 IEC 60250
Dissipation Factor 8 (1 MHz)
 
 IEC 60250
Comparative Tracking Index
V
 IEC 60112
Electric Strength 8
V/mil
 IEC 60243-1
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL 9 (0.0315 in)
 
 UL 94
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Badalac® ABS 10 TM-Z2, Badalac ABS 10 TMZ2, Badalac® , Badalac, BadalacABS10TMZ2, ABS 10 TM, ABS 10 TM Z 2, ABS10TM, ABS 10 TM-Z2, ABS 10 TMZ2, ABS 10 TM:Z2, ABS 10 TM/Z2, ABS 10 TM+Z2, ABS 10 TM_Z2, ABS 10 TM Z2, ABS10, 10TM, TMZ, Z2, ABS10TMZ2, ABS10TM_Z2, Acrylonitrile Butadiene Styrene, ABS, Bada Euro, AcrylonitrileButadieneStyrene, 10ABS
Features
Features may also be described by the following terms: Ultra High Toughness.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Notes
1Typical properties: these are not to be construed as specifications.
223°C
3Test Specimen accordng to ISO 3167, Type A
480x10x4 mm
5110x10x4 mm
6Compound for moulding
7>=10x10x4 mm
880x80x1 mm
9125x13x0.8 mm
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.