IDES Prospector Already have an account? Login Here

IDES

Arnite® AV2 390 XL

Polyethylene Terephthalate

Glass Fiber Reinforcement, 50%

Supplied by DSM Engineering Plastics

The technical datasheet with complete property values for Arnite® AV2 390 XL is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Filler / Reinforcement 
  • Glass Fiber Reinforcement, 50% Filler by Weight
Features 
  • Low to No Outgassing
Automotive Specifications 
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Water Absorption
     ISO 62
Saturation, 73°F
%
  
Equilibrium, 73°F, 50% RH
%
  
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ISO 527-2
Tensile Stress (Break)
psi
 ISO 527-2
Tensile Strain (Break)
%
 ISO 527-2
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength
     ISO 179/1eA
-22°F
ft·lb/in²
  
73°F
ft·lb/in²
  
Charpy Unnotched Impact Strength
     ISO 179/1eU
-22°F
ft·lb/in²
  
73°F
ft·lb/in²
  
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature
      
66 psi, Unannealed
°F
 ISO 75-2/B
264 psi, Unannealed
°F
 ISO 75-2/A
CLTE
     ISO 11359-2
Flow
in/in/°F
  
Transverse
in/in/°F
  
Electrical
Nominal Value
Unit
Test Method
Volume Resistivity
ohm·cm
 IEC 60093
Relative Permittivity
     IEC 60250
100 Hz
 
  
1 MHz
 
  
Dissipation Factor
     IEC 60250
100 Hz
 
  
1 MHz
 
  
Comparative Tracking Index
V
 IEC 60112
Flammability
Nominal Value
Unit
Test Method
Flammability Classification
     IEC 60695-11-10, -20
0.0319 in
 
  
0.0579 in
 
  
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Arnite® AV2 390 XL, Arnite AV2 390 XL, Arnite® , Arnite, ArniteAV2390XL, AV 2 390 XL, AV2 390 XL, AV2, 2390, 390XL, AV2390XL, Polyethylene Terephthalate, PET, Polyester, DSM EP, PolyethyleneTerephthalate, 2AV
Features
Features may also be described by the following terms: Low Outgassing.
Automotive Specifications
This plastic material has approval for 1 automotive specifications from the following agencies (the number in parentheses shows the number of specifications for that agency): GM (1).
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Suggested Max Moisture
%
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Nozzle Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.