IDES Prospector Already have an account? Login Here

IDES

Durez® 00152 Black (Injection)

Phenolic

Supplied by Sumitomo Bakelite North America

The technical datasheet with complete property values for Durez® 00152 Black (Injection) is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Durez 152 Phenolic is a two-stage, heat resistant/ electrical molding material. It exhibits superior dimensional stability, good strength retention at elevated temperature and good molded appearance and machinability which account for it's widespread use on electrical, telecommunication and appliance applications.
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Features 
  • Fungus Resistant
  • Good Dimensional Stability
  • High Temperature Strength
  • Machinable
  • Medium Heat Resistance
  • Pleasing Surface Appearance
Uses 
  • Appliances
  • Electrical/Electronic Applications
  • Telecommunications
Agency Ratings 
 
Appearance 
  • Black
Forms 
  • Granules
Processing Method 
  • Injection Molding
  • Resin Transfer Molding
  
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Apparent Density
g/cm³
 ASTM D1895
Molding Shrinkage - Flow
in/in
 ASTM D6289
Water Absorption
%
 ASTM D570
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ASTM D638
Tensile Strength
psi
 ASTM D638
Flexural Strength
psi
 ASTM D790
Compressive Strength
psi
 ASTM D695
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact
ft·lb/in
 ASTM D256
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load (264 psi, Unannealed)
°F
 ASTM D648
Electrical
Nominal Value
Unit
Test Method
Volume Resistivity
ohm·cm
 ASTM D257
Dielectric Strength
     ASTM D149
-- 2
V/mil
  
-- 3
V/mil
  
Dielectric Constant (1 MHz)
 
 ASTM D2520
Dissipation Factor (1 MHz)
 
 ASTM D150
Comparative Tracking Index
V
 IEC 60112
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL
     UL 94
0.0591 in
 
  
0.118 in
 
  
0.236 in
 
  
UL
Nominal Value
Unit
Test Method
RTI Elec (0.118 in)
°F
 UL 746
Thermoset
Nominal Value
Unit
Test Method
Shelf Life
wk
  
Additional Information
Test Specimens Molded at 340-350°F
Typical transfer-molded shrinkage is 0.008 in/in
Durez 152 is fungus resistant per Mil-I-631D and Mil-E-5272C.
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Durez® 00152 Black, Durez 00152 Black, Durez® 00152 Black (Injection), Durez 00152 Black Injection, Durez® , Durez, Durez00152BlackInjection, 00152 Black, 00152 Black (Injection), 00152 Black Injection, 00152Black, BlackInjection, 00152BlackInjection, Phenolic, Sumitomo Bakelite North America, Black00152
Features
Features may also be described by the following terms: Medium Heat Resistance, Good Dimensional Stability, Dimensionally Stable, Pleasing Surface Appearance, High Temperature Strength.
Uses
Uses may also be described by the following terms: Electrical Applications, Electronic Applications, Electrical/Electronic Applications, Electrical Sector.
Agency Ratings
This plastic material has 2 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): MIL (2).
Notes
1Typical properties: these are not to be construed as specifications.
2Method A (Short-Time)
3Method B (Step-by-Step)
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.