IDES Prospector Already have an account? Login Here

IDES

ABEL PBT FR-G30FT

Polybutylene Terephthalate

Supplied by Shanghai Hongjinyin Industry Co., Ltd.

The technical datasheet with complete property values for ABEL PBT FR-G30FT is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
  • Asia Pacific
  • Europe
  • North America
  • South America
Features 
  • Good Dimensional Stability
  • Good Toughness
  • High Heat Resistance
  • Low Warpage
  
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Molding Shrinkage - Flow
in/in
 ASTM D955
Water Absorption (Saturation)
%
 ASTM D570
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength
psi
 ASTM D638
Flexural Strength
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength
ft·lb/in²
 ISO 179
Charpy Unnotched Impact Strength
ft·lb/in²
 ISO 179
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load (264 psi, Unannealed, 0.252 in)
°F
 ASTM D648
Electrical
Nominal Value
Unit
Test Method
Volume Resistivity
ohm·cm
 ASTM D257
Dielectric Strength (0.0787 in)
V/mil
 ASTM D149
Dielectric Constant (1.00E+7 GHz)
 
 ASTM D150
Dissipation Factor (1.00E+7 GHz)
 
 ASTM D150
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL
 
 UL 94
UL File Number
 
  
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: ABEL PBT FR-G30FT, ABEL PBT FRG30FT, ABEL PBT , ABELPBTFRG30FT, ABELPBT, PBTFR G 30 FT, FR, PBTFR-G30FT, PBTFRG30FT, PBTFR:G30FT, PBTFR/G30FT, PBTFR+G30FT, PBTFR_G30FT, PBTFR G30FT, PBTFRG, PBTFR, FR G 30 FT, FR-G30FT, FRG30FT, FR:G30FT, FR/G30FT, FR+G30FT, FR_G30FT, FR G30FT, FRG, G30, 30FT, Polybutylene Terephthalate, PBT, Polyester, Shanghai Hongjinyin Industry, PolybutyleneTerephthalate, GFR, GPBTFR
Features
Features may also be described by the following terms: Good Dimensional Stability, Dimensionally Stable, High Heat Resistance, Good Toughness, Tough, Low Warpage, Low Warp.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Nozzle Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Injection Pressure
psi
  
Back Pressure
psi
  
Screw Speed
rpm
  
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.