RALUPOL UP 4685/4686/4687 RASCHIG Polyester Alloy (Glass\Inorganic)

Product Description

Applications

Moulded parts in electrical engineering

Break block-wear indicator (car)

Product characteristics
Short glass fibre reinforced, inorganically filled UP moulding compound
Low mould shrinkage and post-shrinkage, good electrical values, good heat resistance, good mechanical values, similar to UP 802
Free of halogens and toxic heavy metals

General

Material Status

Commercial: Active

Availability

Africa & Middle East

Asia Pacific

Europe

Latin America

North America

South America

Filler / Reinforcement

Glass\Inorganic

Features

Good Electrical Properties

Halogen Free

High Heat Resistance

Low Shrinkage

Non-Toxic

Uses

Automotive Applications

Electrical Parts

Engineering Parts

Forms

Granules

Processing Method

Compression Molding

Injection Molding

Physical	Nominal Value	Unit	Test Method
Density		g/cm³	ISO 1183
Apparent Density		g/cm³	ISO 60
Molding Shrinkage			ISO 294-4
--²		%
--³		%
--⁴		%
Water Absorption⁵ (73°F)		mg	ISO 62
Mechanical	Nominal Value	Unit	Test Method
Tensile Stress			ISO 527-2
Yield, 73°F, Compression Molded		psi
Yield, 73°F, Injection Molded		psi
Flexural Strength			ISO 178
73°F, Compression Molded		psi
73°F, Injection Molded		psi
Compressive Stress (73°F)		psi	ISO 604
Impact	Nominal Value	Unit	Test Method
Charpy Notched Impact Strength			ISO 179/1eA
73°F, Compression Molded		ft·lb/in²
73°F, Injection Molded		ft·lb/in²
Charpy Unnotched Impact Strength			ISO 179/1eU
73°F, Compression Molded		ft·lb/in²
73°F, Injection Molded		ft·lb/in²
Hardness	Nominal Value	Unit	Test Method
Ball Indentation Hardness⁶		psi	ISO 2039-1
Thermal	Nominal Value	Unit	Test Method
Heat Deflection Temperature³
66 psi, Unannealed		°F	ISO 75-2/B
264 psi, Unannealed		°F	ISO 75-2/A
1160 psi, Unannealed		°F	ISO 75-2/C
Maximum Use Temperature			IEC 216
--⁷		°F
--⁸		°F
CLTE - Flow (68 to 158°F)		in/in/°F	ISO 11359-2
Electrical	Nominal Value	Unit	Test Method
Surface Resistivity		ohms	IEC 60093
Volume Resistivity		ohm·cm	IEC 60093
Dielectric Constant (100 Hz)			IEC 60250
Dissipation Factor (100 Hz)			IEC 60250
Comparative Tracking Index		V	IEC 60112
Electric Strength (0.0394 in)		V/mil	IEC 60243-1
Needle Flame Test			VDE 0471/2
Flammability	Nominal Value	Unit	Test Method
Flame Rating - UL (0.0630 in)			UL 94
Glow Wire Ignition Temperature		°F	VDE 0471/2
Additional Information	Nominal Value	Unit	Test Method
Glow Wire Test - BH2		in	IEC 707
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: RALUPOL® UP 4685/4686/4687, RALUPOL UP 468546864687, RALUPOL® , RALUPOL, RALUPOLUP468546864687, UP 4685, UP 4685/4686/4687, UP 468546864687, UP 4685:4686:4687, UP 4685+4686+4687, UP 4685-4686-4687, UP 4685_4686_4687, UP 4685 4686 4687, UP4685, 46854686, 46864687, UP468546864687, UP4685_4686_4687, Polyester Alloy, Polyester, RASCHIG, PolyesterAlloy, 4685UP
Features
Features may also be described by the following terms: Low Shrinkage, Good Electrical Properties, High Heat Resistance, Zero Halogen Content, Halogen Free, Non-Toxic, Non Toxic, Toxicity None.
Uses
Uses may also be described by the following terms: Engineering Parts, Automotive Applications, Automotive Sector.

Injection	Nominal Value	Unit
Processing (Melt) Temp		°F
Mold Temperature		°F
Injection Notes
Barrel Temperature: 60 - 80°C to 80 - 100°C

Notes

¹Typical properties: these are not to be construed as specifications.

²Post-shrink

³Injection molded

⁴Compression molded

⁵96 hrs

⁶23°C

⁷< 50 hrs, T1

⁸20000 hrs, T1

RALUPOL® UP 4685/4686/4687

Polyester Alloy

Glass\Inorganic

Supplied by RASCHIG GmbH