IDES Prospector Already have an account? Login Here

IDES

Arak LLDPE LL1209AA / LL1209KJ

Linear Low Density Polyethylene

Supplied by Arak Petrochemical Corporation

The technical datasheet with complete property values for Arak LLDPE LL1209AA / LL1209KJ is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
LL1209AA & LL1209KJ are linear low density polyethylene copolymers containing butene-1 as a co-monomer. LL1209AA & LL1209KJ are suitable for co extrusion blown films with the following advantages:
  • Improved hot-tack.
  • Good optical properties.
  • Low gel level and low odour.
  • Good substrate adhesion.
  • Tough core layer.

Typical applications for LL1209AA & LL1209KJ are lamination films and heat sealing layers. Also LL1209KJ is highly recommended for display packaging.

LL1209KJ offers high slip film with easy opening properties when used pure in thickness range 35-100 microns. Addition of other polymers, master batches and pigments or use of other thickness may alter film slip and anti-block performance.

Recommended melt temperature for extrusion is about 180°C-225°C.

LL1209AA & LL1209KJ should be stored in the dry condition below the 50°C and avoided from the exposure of direct sunlight.

* LL1209AA & LL1209KJ are suitable for food contact.
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
Additive 
  • High Slip
Features 
  • Butene Comonomer
  • Copolymer
  • Food Contact Acceptable
  • Good Adhesion
  • Good Heat Seal
  • Good Toughness
  • High Slip
  • Hot Tack Strength
  • Low Gloss
  • Low to No Odor
  • Opticals
Uses 
  • Cable Jacketing
  • Film
  • Laminates
  • Packaging
  
Processing Method 
  • Blown Film
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ASTM D2838
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)
g/10 min
 ASTM D1238
Films
Nominal Value
Unit
Test Method
Film Thickness - Tested
mil
  
Film Thickness - Recommended / Available
 
  
Tensile Strength
     ASTM D882
MD: Yield
psi
  
TD: Yield
psi
  
MD: Break
psi
  
TD: Break
psi
  
Tensile Elongation
     ASTM D882
MD: Break
%
  
TD: Break
%
  
Dart Drop Impact
g
 ASTM D1709
Elmendorf Tear Strength
     ASTM D1922
MD: 0.98 mil
g
  
TD: 0.98 mil
g
  
Optical
Nominal Value
Unit
Test Method
Gloss (45°)
 
 ASTM D2457
Haze
%
 ASTM D1003
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Arak LLDPE LL1209AA / LL1209KJ, Arak LLDPE LL1209AA LL1209KJ, Arak LLDPE , ArakLLDPELL1209AALL1209KJ, ArakLLDPE, LL 1209 AA, LLDPELL 1209 AA LL 1209 KJ, LLDPELL 1209 AA, LL1209AA, LLDPELL1209AA / LL1209KJ, LLDPELL1209AA LL1209KJ, LLDPELL1209AA : LL1209KJ, LLDPELL1209AA + LL1209KJ, LLDPELL1209AA - LL1209KJ, LLDPELL1209AA _ LL1209KJ, LLDPELL1209AA LL1209KJ, LLDPELL1209, LLDPELL1209AA, LL 1209 AA LL 1209 KJ, LLDPELL1209AALL1209KJ, LL1209AA / LL1209KJ, LL1209AA LL1209KJ, LL1209AA : LL1209KJ, LL1209AA + LL1209KJ, LL1209AA - LL1209KJ, LL1209AA _ LL1209KJ, LL1209AA LL1209KJ, LL1209, 1209AA, AALL, 1209KJ, LLDPELL1209AA_LL1209KJ, LL1209AALL1209KJ, LL1209AA_LL1209KJ, Polyethylene, Linear Low Density, Polyethylene Linear Low Density, LLDPE, Polyethylene, PE, Arak Petrochemical, PolyethyleneLinearLowDensity, 1209LL, 1209LLDPELL
Features
Features may also be described by the following terms: Butene Comonomer, Good Heat Seal, Hot Tack Strength, Good Adhesion, Low Gloss, Low Odor, High Slip, Good Toughness, Tough.
Extrusion
Nominal Value
Unit
 
Melt Temperature
°F
  
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.