IDES Prospector Already have an account? Login Here

IDES

TAROMID A 280 H MG6 DX0

Polyamide 66

Mineral Filler, 30%

Supplied by Taro Plast S.p.A.

The technical datasheet with complete property values for TAROMID A 280 H MG6 DX0 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Polyamide 66 medium viscosity, 30% mineral fiber reinforced, UL94 V0 self extinguishing, Material PBDE/PBDF free.

UL94 V0 approved - NC@ 0,75 mm

Available: all colours, UV-stabilised (L), heat-stabilised (H), release agent (W), elastomer modified (R).
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Filler / Reinforcement 
  • Mineral Filler, 30% Filler by Weight
Additive 
  • Heat Stabilizer
  • Impact Modifier
  • Mold Release
  • UV Stabilizer
  
Features 
  • Good Mold Release
  • Good UV Resistance
  • Heat Stabilized
  • Impact Modified
  • Medium Viscosity
  • Self Extinguishing
Appearance 
  • Colors Available
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
      
--
 
 ASTM D792
--
g/cm³
 ISO 1183
Molding Shrinkage
     ASTM D955
Flow
in/in
  
Across Flow
in/in
  
Water Absorption
      
73°F, 24 hr
%
 ASTM D570, ISO 62
Saturation
%
 ASTM D570
Saturation, 73°F
%
 ISO 62
Granule Humidity
%
 Internal Method
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ASTM D638, ISO 527-2
Tensile Strength (Break)
psi
 ASTM D638, ISO 527-2
Tensile Elongation (Break)
%
 ASTM D638, ISO 527-2
Flexural Modulus
psi
 ASTM D790, ISO 178
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact (73°F, 0.126 in)
ft·lb/in
 ISO 180, ASTM D256
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load (264 psi, Unannealed)
°F
 ASTM D648, ISO 75-2/A
Max. Continuous Use Temperature
°F
 UL 746B
Vicat Softening Temperature
      
--
°F
 ASTM D1525 2, ISO 306/A50 2
--
°F
 ASTM D1525 3, ISO 306/B50 3
Ball Pressure Test (329°F)
 
 VDE 0470
CLTE - Flow (-22 to 86°F)
in/in/°F
 ASTM D696
Electrical
Nominal Value
Unit
Test Method
Volume Resistivity
ohm·cm
 ASTM D257
Comparative Tracking Index (Solution A)
V
 IEC 60112
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL
     UL 94
0.0295 in
 
  
0.126 in
 
  
Glow Wire Ignition Temperature (0.0787 in)
°F
 IEC 60695-2-13
Oxygen Index
%
 ASTM D2863
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: TAROMID A 280 H MG6 DX0, TAROMID A , TAROMIDA280HMG6DX0, TAROMIDA, A 280 H MG 6 DX 0, A280 H MG6 DX0, A280, 280 H MG 6 DX 0, A280HMG6DX0, 280 H MG6 DX0, 280H, HMG, MG6, 6DX, DX0, 280HMG6DX0, Polyamide 66, Nylon 66, Polyamide, Nylon, pa66, Taro Plast, Polyamide66, Nylon66, H280, 280A
Generic Name
Generic Name may also be described by the following terms: PA66.
Features
Features may also be described by the following terms: Medium Viscosity, Heat Stabilized, Heat-ageing Stabilized, Heat Ageing Stabilized, Heat-aging Stabilized, Heat Aging Stabilized, Good Mold Release, Easy Release, Good Demolding, Self Extinguishing, Self-Extinguishing, Good UV Resistance, UV Resistant, Ultraviolet Resistant, Ultraviolet Light Resistant.
Injection
Nominal Value
Unit
 
Drying Temperature
      
--
°F
  
Pre-heater
°F
  
Drying Time
      
--
hr
  
Pre-heater
hr
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Injection Rate
 
  
Notes
1Typical properties: these are not to be construed as specifications.
2Rate A (50°C/h), Loading 1 (10 N)
3Rate A (50°C/h), Loading 2 (50 N)
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.