IDES Prospector Already have an account? Login Here

IDES

Lustran® SMA 2316

Styrene Maleic Anhydride

Glass Fiber Reinforcement, 16%

Supplied by INEOS ABS (USA)

The technical datasheet with complete property values for Lustran® SMA 2316 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Filler / Reinforcement 
  • Glass Fiber Reinforcement, 16% Filler by Weight
Agency Ratings 
Automotive Specifications 
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
      
--
 
  
--
g/cm³
  
Melt Mass-Flow Rate (MFR) (220°C/10.0 kg)
g/10 min
  
Molding Shrinkage
     ISO 2577
Across Flow
%
  
Flow
%
  
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ISO 527-2
Tensile Stress
     ISO 527-2
Yield
psi
  
Break
psi
  
Flexural Modulus
psi
 ISO 178
Flexural Strength 2
psi
 ISO 178
Poisson's Ratio 3
 
  
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength
     ISO 179/1eA
-22°F
ft·lb/in²
  
73°F
ft·lb/in²
  
Notched Izod Impact Strength 4
     ISO 180/1A
-40°F
ft·lb/in²
  
73°F
ft·lb/in²
  
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature
      
66 psi, Unannealed, 0.157 in Span
°F
 ISO 75-2/B
264 psi, Unannealed, 0.157 in Span
°F
 ISO 75-2/A
Vicat Softening Temperature
°F
 ISO 306/B50
CLTE
     ISO 11359-2
Flow
in/in/°F
  
Transverse
in/in/°F
  
Flammability
Nominal Value
Unit
Test Method
Burning Rate
in/min
 SAE J369
Related Terminology
This supplier and product may also be known by these terms: INEOS Styrenics

Product names can be difficult to match. You may have searched any one of these terms to find this product: Lustran® SMA 2316, Lustran SMA 2316, Lustran® SMA , Lustran SMA, LustranSMA2316, LustranSMA, SMA 2316, SMA2316, SMA, 2316, Styrene Maleic Anhydride, smah, Ineos ABS (USA), StyreneMaleicAnhydride, 2316SMA
Automotive Specifications
This plastic material has approval for 3 automotive specifications from the following agencies (the number in parentheses shows the number of specifications for that agency): FORD (1), CHRYSLER (1), GM (1).
Agency Ratings
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): EC (1).
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Nozzle Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Injection Rate
 
  
Back Pressure
psi
  
Clamp Tonnage
tons/in²
  
Cushion
in
  
Notes
1Typical properties: these are not to be construed as specifications.
2Yield
3Across Flow: 0.39
44x10 mm
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.