IDES Prospector Already have an account? Login Here

IDES

GETILAN ATP/130 XP

Crosslinked Polyethylene

Supplied by Crosspolimeri S.p.A.

The technical datasheet with complete property values for GETILAN ATP/130 XP is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
GETILAN ATP/130 XP is a crosslinkable polythene.
GETILAN ATP/130 XP is a high density chemically crosslinkable polythene to produce relatively flexible hoses suitable for hydro-thermosanitary features and also for water conduction.
It is a conveniently grafted polythene able to react in presence of moisture and of catalyst.
We normally suggest our type MAC/100 PSF.
REACTION BETWEEN GRAFTING AND CATALYST
These two polythenes, separately stored, must be mixed before starting extrusion in the ratio:
GRAFTING/CATALYST 95/5
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Features 
  • Crosslinkable
  • High Density
  
Uses 
  • Hose
  • Wire & Cable Applications
  
Agency Ratings 
Forms 
  • Pellets
Processing Method 
  • Extrusion
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Melt Mass-Flow Rate (MFR) (190°C/5.0 kg)
g/10 min
 ASTM D1238
Mechanical
Nominal Value
Unit
Test Method
Tensile Stress (Yield)
psi
 IEC 60811
Tensile Strain (Break)
%
 IEC 60811
Hardness
Nominal Value
Unit
Test Method
Durometer Hardness (Shore D)
 
 ASTM D2240
Thermal
Nominal Value
Unit
Test Method
Vicat Softening Temperature
°F
 ASTM D1525
Service Temperature
°F
  
Additional Information
Nominal Value
Unit
Test Method
Pressure Test
      
203°F 2
 
  
203°F 3
 
  
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: GETILAN ATP/130 XP, GETILAN ATP130 XP, GETILAN , GETILANATP130XP, ATP, ATP/130 XP, ATP130 XP, ATP:130 XP, ATP+130 XP, ATP-130 XP, ATP_130 XP, ATP 130 XP, ATP130, 130XP, ATP130XP, ATP_130XP, Polyethylene, Crosslinked, Polyethylene Crosslinked, XLPE, Polyethylene, PE, Crosspolimeri, PolyethyleneCrosslinked, 130ATP
Features
Features may also be described by the following terms: High Density, High Specific Gravity.
Uses
Uses may also be described by the following terms: Wire and Cable Applications, Wire & Cable Applications.
Agency Ratings
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): DIN (1).
Extrusion
Nominal Value
Unit
 
Cylinder Zone 1 Temp.
°F
  
Cylinder Zone 2 Temp.
°F
  
Cylinder Zone 3 Temp.
°F
  
Cylinder Zone 4 Temp.
°F
  
Cylinder Zone 5 Temp.
°F
  
Die Temperature
°F
  
Extrusion Notes
CROSSLINKING:
Crosslinking of the finished product is obtained by:
  • Immersion of the bobbin into hot water at 85/90°C for two hours (up to 3 mm thickness).
  • Steam treatment at 0.15 bar for 5/6 hours.
Notes
1Typical properties: these are not to be construed as specifications.
21 hr, 4.8 MPa
31000 hr, 4.4 MPa
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.