IDES Prospector Already have an account? Login Here

IDES

GETILAN ATP/190 3AP

Crosslinked Polyethylene

Supplied by Crosspolimeri S.p.A.

The technical datasheet with complete property values for GETILAN ATP/190 3AP is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
GETILAN ATP/190 3AP is a crosslinkable (SIOPLAS technology) polyolefinic compound.
GETILAN ATP/190 3AP is a high density antiflame chemically crosslinkable polythene with high temperature index and low HCl content. Suitable for automotive cables insulation.
It is a conveniently grafted polythene able to react in presence of moisture and of catalyst.
We normally suggest our catalyst type MAC/203 HS or MAC/203 HSL (less reactive)..
REACTION BETWEEN GRAFTING AND CATALYST
These two polythenes, separately stored, must be mixed before starting extrusion in the ratio:
GRAFTING/CATALYST 96/4
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Features 
  • Crosslinkable
  • High Density
  
Uses 
  • Automotive Applications
  • Insulation
  • Wire & Cable Applications
Agency Ratings 
 
Forms 
  • Pellets
Processing Method 
  • Extrusion
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength
psi
 ASTM D638
Tensile Elongation (Break)
%
 ASTM D638
Hardness
Nominal Value
Unit
Test Method
Durometer Hardness (Shore D)
 
 ASTM D2240
Thermal
Nominal Value
Unit
Test Method
Hot Set 2
     IEC 60811
392°F
%
  
Residual: 392°F
%
  
Service Temperature
°F
  
Aging
Nominal Value
Unit
Test Method
Heat Aging
     IEC 60811
240 hr: 302°F
 
  
6 hr: 347°F
 
  
Flammability
Nominal Value
Unit
Test Method
Oxygen Index
%
 ASTM D2863
Halogen Content
%
 IEC 60754-1
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: GETILAN ATP/190 3AP, GETILAN ATP190 3AP, GETILAN , GETILANATP1903AP, ATP, ATP 190 3 AP, ATP/190 3AP, ATP190 3AP, ATP:190 3AP, ATP+190 3AP, ATP-190 3AP, ATP_190 3AP, ATP 190 3AP, ATP190, 1903, 3AP, ATP1903AP, ATP_1903AP, Polyethylene, Crosslinked, Polyethylene Crosslinked, XLPE, Polyethylene, PE, Crosspolimeri, PolyethyleneCrosslinked, 190ATP
Features
Features may also be described by the following terms: High Density, High Specific Gravity.
Uses
Uses may also be described by the following terms: Automotive Applications, Automotive Sector, Wire and Cable Applications, Wire & Cable Applications.
Agency Ratings
This plastic material has 4 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): ISO (1), LV (1), SAE (2).
Extrusion
Nominal Value
Unit
 
Cylinder Zone 1 Temp.
°F
  
Cylinder Zone 2 Temp.
°F
  
Cylinder Zone 3 Temp.
°F
  
Cylinder Zone 4 Temp.
°F
  
Cylinder Zone 5 Temp.
°F
  
Die Temperature
°F
  
Extrusion Notes
CROSSLINKING:
Crosslinking of the finished product is obtained by:
  • Immersion of the bobbin into hot water at 85/90°C for two hours (up to 3 mm thickness).
  • Steam treatment at 0.15 for bar 5/6 hours.
  • Faster ambient curing is possible depending from the atmospheric conditions.
Notes
1Typical properties: these are not to be construed as specifications.
220 N/cm²
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.