IDES Prospector Already have an account? Login Here

IDES

Bio-Flex® S 6540

Biodegradable Polymers

Supplied by FKuR Kunststoff GmbH

The technical datasheet with complete property values for Bio-Flex® S 6540 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Biodegradable resin for manufacture of injection moulded parts
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Features 
  • Biodegradable
  • Renewable Resource Content
  
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Apparent Density
g/cm³
 ISO 60
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)
g/10 min
 ISO 1133
Melt Volume-Flow Rate (MVR) (190°C/2.16 kg)
in³/10min
 ISO 1133
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ISO 527-2
Tensile Stress
     ISO 527-2
Yield
psi
  
Break
psi
  
Tensile Strain (Break)
%
 ISO 527-2
Flexural Modulus
psi
 ISO 178
Flexural Strength
     ISO 178
-- 2
psi
  
3.5% Strain
psi
  
Tensile Strain at Tensile Strength
%
 ISO 527-2
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength (73°F)
ft·lb/in²
 ISO 179/1eA
Charpy Unnotched Impact Strength (73°F)
ft·lb/in²
 ISO 179/1eU
Thermal
Nominal Value
Unit
Test Method
Vicat Softening Temperature
°F
 ISO 306/A
Melting Temperature (DSC)
°F
 ISO 3146
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Bio-Flex® S 6540, BioFlex S 6540, Bio-Flex® , BioFlex, Bio:Flex®, Bio/Flex®, Bio+Flex®, Bio_Flex®, Bio Flex®, BioFlexS6540, Bio_Flex, Bio Flex, S 6540, S6540, Biodegradable Polymers, Biodeg Polymers, FKuR, BiodegradablePolymers, BiodegPolymers, 6540S
Features
Features may also be described by the following terms: Renewable Resources, From Renewable Resources, Renewable Resource Derived, Renewable Raw Materials, Renewable Resource Content.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Suggested Max Moisture
%
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Nozzle Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Injection Pressure
psi
  
Back Pressure
psi
  
Injection Notes
Feeding zone: 40°C
Cylinder kneeling temp: 140°C
Screw peripheral velocity: up to 200 mm/s
Holding pressure time: 20 to 45 sec
Melt cushion (of volume): 3 to 10%
Cooling time: 10 to 60 sec
Notes
1Typical properties: these are not to be construed as specifications.
2Break
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.