IDES Prospector Already have an account? Login Here

IDES

AvaSpire® AV-848

Polyaryletherketone

Supplied by Solvay Specialty Polymers

The technical datasheet with complete property values for AvaSpire® AV-848 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
AvaSpire® AV-848 is a high-temperature, polyaryletherketone (PAEK) that offers several key performance advantages over comparable grades of PEEK above 150°C, including better dimensional stability, lower CLTE from 150°C to 240°C, and lower modulus for greater flexibility at room temperature.

  • Natural: AvaSpire AV-848 NT
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
  • Asia Pacific
  • Europe
  • North America
  • South America
Features 
  • Ductile
  • Fatigue Resistant
  • Flame Retardant
  • Good Chemical Resistance
  • Good Dimensional Stability
  • Good Impact Resistance
  • High Heat Resistance
Uses 
  • Oil/Gas Applications
  • Seals
  
RoHS Compliance 
Appearance 
  • Natural Color
Forms 
  • Pellets
Processing Method 
  • Extrusion Blow Molding
  • Fiber (Spinning) Extrusion
  • Film Extrusion
  • Injection Blow Molding
  • Injection Molding
  • Machining
  • Profile Extrusion
  • Thermoforming
  • Wire & Cable Extrusion
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Water Absorption (24 hr)
%
 ASTM D570
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus 2
psi
 ASTM D638
Tensile Strength 2
psi
 ASTM D638
Tensile Elongation
     ASTM D638
Yield 2
%
  
Break 3
%
  
Break 2
%
  
Flexural Modulus
psi
 ASTM D790
Flexural Strength
psi
 ASTM D790
Compressive Strength
psi
 ASTM D695
Shear Strength
psi
 ASTM D732
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact
ft·lb/in
 ASTM D256
Unnotched Izod Impact
 
 ASTM D4812
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load (264 psi, Annealed)
°F
 ASTM D648
Glass Transition Temperature (DSC)
°F
 ASTM D3418
Peak Melting Temperature
°F
 ASTM D3418
Specific Heat
     DSC
122°F
Btu/lb/°F
  
392°F
Btu/lb/°F
  
Thermal Conductivity
Btu·in/hr/ft²/°F
 ASTM E1530
Electrical
Nominal Value
Unit
Test Method
Dielectric Strength (0.118 in)
V/mil
 ASTM D149
Dielectric Constant
     ASTM D150
60 Hz
 
  
1 kHz
 
  
1 MHz
 
  
Dissipation Factor
     ASTM D150
60 Hz
 
  
1 kHz
 
  
1 MHz
 
  
Fill Analysis
Nominal Value
Unit
Test Method
Melt Viscosity 4
Pa·s
 ASTM D3835
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: AvaSpire® AV-848, AvaSpire AV848, AvaSpire® , AvaSpire, AvaSpireAV848, AV, AV-848, AV848, AV:848, AV/848, AV+848, AV_848, AV 848, Polyaryletherketone, PAEK, Solvay Specialty, 848AV
Features
Features may also be described by the following terms: Good Dimensional Stability, Dimensionally Stable, Good Chemical Resistance, Chemical Resistant, High Heat Resistance, Good Impact Resistance.
Uses
Uses may also be described by the following terms: Oil Applications, Gas Applications.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Nozzle Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Injection Rate
 
  
Screw Compression Ratio
 
  
Injection Notes
Back Pressure: Minimum
Notes
1Typical properties: these are not to be construed as specifications.
22.0 in/min
30.20 in/min
4@400°C/1000 sec-1
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.