IDES Prospector Already have an account? Login Here

IDES

Kingfa AIP-2503HM

Polypropylene

Talc Filler, 25%

Supplied by Kingfa

The technical datasheet with complete property values for Kingfa AIP-2503HM is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
PP-EPDM-T25
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
Filler / Reinforcement 
  • Talc Filler, 25% Filler by Weight
Additive 
  • Rubber 1
  • UV Stabilizer
  
Features 
  • Good Toughness
  • Good UV Resistance
  • High Stiffness
Uses 
  • Automotive Instrument Panel
  • Automotive Interior Parts
  
Automotive Specifications 
Appearance 
  • Unspecified Color
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Melt Mass-Flow Rate (MFR) (230°C/2.16 kg)
g/10 min
 ISO 1133
Molding Shrinkage (73°F)
%
 Internal Method
Ash Content 3 (1382°F)
%
 ISO 3451
Mechanical
Nominal Value
Unit
Test Method
Tensile Stress (Break)
psi
 ISO 527-2/50
Tensile Strain (Break)
%
 ISO 527-2/50
Flexural Modulus 4
psi
 ISO 178
Flexural Strength 4
psi
 ISO 178
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact Strength 5 (73°F)
ft·lb/in²
 ISO 180
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature (66 psi, Unannealed, 0.157 in Span)
°F
 ISO 75-2/B
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL 6
 
 ISO 3795
Additional Information
Nominal Value
Unit
Test Method
Weather Resistance 7
 
 SAE J1960
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Kingfa AIP-2503HM, Kingfa AIP2503HM, Kingfa , KingfaAIP2503HM, AIP, AIP 2503 HM, AIP-2503HM, AIP2503HM, AIP:2503HM, AIP/2503HM, AIP+2503HM, AIP_2503HM, AIP 2503HM, AIP2503, 2503HM, Polypropylene, Unspecified, Polypropylene Unspecified, PP, Unspecified, PP Unspecified, Polypropylene, PP, PolypropyleneUnspecified, PPUnspecified, 2503AIP
Generic Name
Generic Name may also be described by the following terms: Polypropilene, Polypropelene.
Features
Features may also be described by the following terms: Good UV Resistance, UV Resistant, Ultraviolet Resistant, Ultraviolet Light Resistant, Good Toughness, Tough, High Stiffness.
Uses
Uses may also be described by the following terms: Automotive Instrument Panel, Automotive Dash Board.
Automotive Specifications
This plastic material has approval for 1 automotive specifications from the following agencies (the number in parentheses shows the number of specifications for that agency): FORD (1).
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Injection Rate
 
  
Back Pressure
psi
  
Injection Notes
Processing Temp. Limit: 250°C
Notes
1EPDM
2Typical properties: these are not to be construed as specifications.
330 min
40.079 in/min
54 mm
6360×100×3
7250 kJ/m²
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.