SABIC® HDPE 0863F SABIC Polyethylene, High Density

Product Description

High density polyethylene for Extrusion coating:

SABIC® HDPE 0863F resin is a homopolymer with an exceptional high density manufactured by gas phase technology. The grade offers high sitffness, high temperature resistance, low water vapour transmission and relatively high grease resistance. The resin has an extreme low gel level. Because of the linear character it is advisable to use the material in combination with autoclave LDPE in order to improve extrusion coating processability and maintain web stability.

SABIC® HDPE 0863F is typically used for food packaging, release paper and photographic paper.

High density polyethylene for masterbatch compounding

SABIC® HDPE 0863F is a special homopolymer HDPE grade with a very low gel level and good intrinsic stability.

Application

SABIC® HDPE 0863F is specially suited for masterbatches in extrusion coating, in HDPE layers.

Further as masterbatch in general or specific HDPE applications, when stiffness, combined with good flow properties are required, such as injection moulding and film extrusion.

The product mentioned herein is in particular not tested and therefore not validated for use in pharmaceutical/medical applications.

General

Material Status

Commercial: Active

Availability

Europe

Features

Food Contact Acceptable

Good Processability

Good Processing Stability

Grease Resistant

High Heat Resistance

High Stiffness

Low Gel

Low to No Water Absorption

Uses

Coating Applications

Film

Food Packaging

Masterbatch

Release Paper

Processing Method

Cast Film

Compounding

Extrusion Coating

Physical	Nominal Value	Unit	Test Method
Density		g/cm³	ISO 1183
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)		g/10 min	ISO 1133
Films	Nominal Value	Unit	Test Method
Film Thickness - Tested		mil
Tensile Modulus			ISO 527-3
MD: 0.98 mil, Cast Film		psi
TD: 0.98 mil, Cast Film		psi
Tensile Stress			ISO 527-3
MD: Yield, 0.98 mil, Cast Film		psi
TD: Yield, 0.98 mil, Cast Film		psi
MD: Break, 0.98 mil, Cast Film		psi
TD: Break, 0.98 mil, Cast Film		psi
Tensile Elongation			ISO 527-3
MD: Break, 0.98 mil, Cast Film		%
TD: Break, 0.98 mil, Cast Film		%
Water Vapor Transmission Rate (100°F, 0.98 mil, Cast Film, 100% RH)		g/100 in²/24 hr	Internal Method
Oxygen Permeability² (73°F, 1.0 mil)		cm³/cm²/bar	Internal Method
Thermal	Nominal Value	Unit	Test Method
Vicat Softening Temperature		°F	ISO 306/A
Melting Temperature (DSC)		°F	DIN 53765
Enthalpy Change - (DSC)		J/g	DIN 53765
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: SABIC® HDPE 0863F, SABIC HDPE 0863F, SABIC® HDPE , SABIC HDPE, SABICHDPE0863F, SABICHDPE, HDPE 0863 F, HDPE0863F, HDPE0863, HDPE, 0863 F, 0863F, Polyethylene, High Density, Polyethylene High Density, Polyethylene, PE, SABIC, PolyethyleneHighDensity, F0863, 0863HDPE
Features
Features may also be described by the following terms: High Stiffness, High Heat Resistance, Low Water Absorption, Low Moisture Absorption, Water Resistant, Moisure Resistant, Low Gel, Good Processability, Easy Processing, Good Processing Stability, Good Process Stability.
Uses
Uses may also be described by the following terms: Food Packaging.

Notes

¹Typical properties: these are not to be construed as specifications.

²Cast FIlm, 0% RH

SABIC® HDPE 0863F

High Density Polyethylene

Supplied by Saudi Basic Industries Corporation (SABIC)