IDES Prospector Already have an account? Login Here

IDES

Halene H P4600L

High Density Polyethylene

Supplied by Haldia Petrochemicals Ltd.

The technical datasheet with complete property values for Halene H P4600L is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
P4600L is a pipe grade HDPE, produced by the Spherilene Technology.

This resin is recommended for water pipes, sprinkler irrigation pipes and telecom ducts.

P4600L combines exceptional processability with good creep resistance, ESCR and mechanical properties.
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
Features 
  • Good Creep Resistance
  • Good Processability
  • High ESCR (Stress Crack Resist.)
Uses 
  • Piping
Processing Method 
  • Pipe Extrusion
Physical
Nominal Value
Unit
Test Method
Density 2
g/cm³
 ASTM D1505
Melt Mass-Flow Rate (MFR) (190°C/5.0 kg)
g/10 min
 ASTM D1238
Environmental Stress-Cracking Resistance (10% Igepal, Compression Molded, F50)
hr
 ASTM D1693B
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength 3
     ASTM D638
Yield, Compression Molded
psi
  
Break, Compression Molded
psi
  
Tensile Elongation 3
     ASTM D638
Yield, Compression Molded
%
  
Break, Compression Molded
%
  
Flexural Modulus (Compression Molded)
psi
 ASTM D790A
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact (73°F, Compression Molded)
ft·lb/in
 ASTM D256A
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load (66 psi, Unannealed)
°F
 ASTM D648
Vicat Softening Temperature
°F
 ASTM D1525
Peak Melting Temperature
°F
 ASTM D3418
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Halene H P4600L, Halene H , HaleneHP4600L, HaleneH, HP 4600 L, HP4600L, HP4600, P 4600 L, P4600L, P4600, 4600L, Polyethylene, High Density, Polyethylene High Density, HDPE, Polyethylene, PE, Haldia Petrochem, PolyethyleneHighDensity, 4600P, 4600HP
Features
Features may also be described by the following terms: Good Creep Resistance, Creep Resistant, High Environmental Stress Cracking Resistance, High ESCR, Stress Cracking Resistant, Good Processability, Easy Processing.
Uses
Uses may also be described by the following terms: Piping, Pipe.
Extrusion
Nominal Value
Unit
 
Cylinder Zone 1 Temp.
°F
  
Cylinder Zone 2 Temp.
°F
  
Cylinder Zone 3 Temp.
°F
  
Cylinder Zone 4 Temp.
°F
  
Cylinder Zone 5 Temp.
°F
  
Die Temperature
°F
  
Notes
1Typical properties: these are not to be construed as specifications.
227°C
32.0 in/min
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.