IDES Prospector Already have an account? Login Here

IDES

Hostaform® C 9021 AS

Acetal (POM) Copolymer

Supplied by Ticona

The technical datasheet with complete property values for Hostaform® C 9021 AS is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
POM copolymer

Antistatical modified standard flowing Injection molding type the antistatical effect improves, when the molding part absorbs enough humidity good chemical resistance to solvents, fuel and strong alkalis as well as good hydrolysis resistance high resistance to thermal and oxidative degradation.


Hostaform C 9021 AS is suggested for dissipation of minor buildup of static electricity that might occur with standard type grades. However, it is not intended for use in fuel system components where static dissipation is critical to part performance. Please refer to Ticona's ESD (electrostatic dissipative) grades for those applications

Preliminary Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
  • North America
  
Additive 
  • Antistatic
Features 
  • Alkali Resistant
  • Antistatic
  • Fuel Resistant
  • Good Chemical Resistance
  • Hydrolysis Resistant
  • Solvent Resistant
RoHS Compliance 
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Melt Volume-Flow Rate (MVR) (190°C/2.16 kg)
in³/10min
 ISO 1133
Molding Shrinkage
     ISO 294-4
Across Flow
%
  
Flow
%
  
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ISO 527-2/1A/1
Tensile Stress (Yield)
psi
 ISO 527-2/1A/50
Tensile Strain (Yield)
%
 ISO 527-2/1A/50
Nominal Tensile Strain at Break
%
 ISO 527-2/1A/50
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength
     ISO 179/1eA
-22°F
ft·lb/in²
  
73°F
ft·lb/in²
  
Charpy Unnotched Impact Strength
     ISO 179/1eU
-22°F
ft·lb/in²
  
73°F
ft·lb/in²
  
Thermal
Nominal Value
Unit
Test Method
Melting Temperature 2
°F
 ISO 11357-3
CLTE - Flow
in/in/°F
 ISO 11359-2
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity
ohm
 IEC 60093
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Hostaform® C 9021 AS, Hostaform C 9021 AS, Hostaform® , Hostaform, HostaformC9021AS, C 9021 AS, C9021, 9021AS, C9021AS, Acetal Copolymer, Acetal Copolymer, Acetal (POM) Copolymer, Acetal POM Copolymer, Acetal, pom, Ticona, AcetalPOMCopolymer, 9021C
Features
Features may also be described by the following terms: Good Chemical Resistance, Chemical Resistant.
Injection
Nominal Value
Unit
 
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Screw L/D Ratio
 
  
Injection Notes
Standard injection moulding machines with three phase (15 to 25 D)
plasticating screws will fit.
Notes
1Typical properties: these are not to be construed as specifications.
210°C/min
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.