Reny® 2502AH Mitsubishi EP Polyarylamide (Glass\Mineral, 20%)

General

Material Status

Commercial: Active

Availability

Asia Pacific

Europe

North America

Filler / Reinforcement

Glass\Mineral, 20% Filler by Weight

Additive

Flame Retardant

Features

Flame Retardant

Physical	Dry	Conditioned	Unit	Test Method
Density		--	g/cm³	ISO 1183
Melt Mass-Flow Rate (MFR) (275°C/2.16 kg)		--	g/10 min	ISO 1133
Melt Volume-Flow Rate (MVR) (275°C/2.16 kg)		--	in³/10min	ISO 1133
Molding Shrinkage		--	%
Water Absorption				ISO 62
Saturation, 73°F		--	%
Equilibrium, 73°F, 50% RH		--	%
Mechanical	Dry	Conditioned	Unit	Test Method
Tensile Modulus			psi	ISO 527-2
Tensile Stress (Break)			psi	ISO 527-2
Tensile Strain (Break)			%	ISO 527-2
Flexural Modulus			psi	ISO 178
Flexural Strength			psi	ISO 178
Impact	Dry	Conditioned	Unit	Test Method
Charpy Notched Impact Strength (73°F)			ft·lb/in²	ISO 179
Charpy Unnotched Impact Strength (73°F)			ft·lb/in²	ISO 179
Thermal	Dry	Conditioned	Unit	Test Method
Heat Deflection Temperature
66 psi, Unannealed			°F	ISO 75-2/B
264 psi, Unannealed			°F	ISO 75-2/A
CLTE				ISO 11359-2
Flow		--	in/in/°F
Transverse		--	in/in/°F
Electrical	Dry	Conditioned	Unit	Test Method
Surface Resistivity			ohm	IEC 60093
Volume Resistivity			ohm·cm	IEC 60093
Relative Permittivity				IEC 60250
100 Hz	--
1 MHz	--
Dissipation Factor				IEC 60250
100 Hz	--
1 MHz	--
Comparative Tracking Index			V	IEC 60112
Electric Strength				IEC 60243-1
0.0394 in			V/mil
0.0787 in			V/mil
Flammability	Dry	Conditioned	Unit	Test Method
Flame Rating - UL (0.0630 in)		--		UL 94
Related Terminology
Dry	Product names can be difficult to match. You may have searched any one of these terms to find this product: Reny® 2502AH, Reny 2502AH, Reny® , Reny, Reny2502AH, 2502 AH, 2502AH, Polyarylamide, PARA, Polyamide, Nylon, Mitsubishi EP, AH2502
Conditioned	Product names can be difficult to match. You may have searched any one of these terms to find this product: Reny® 2502AH, Reny 2502AH, Reny® , Reny, Reny2502AH, 2502 AH, 2502AH, Polyarylamide, PARA, Polyamide, Nylon, Mitsubishi EP, AH2502

Injection	Dry	Unit
Drying Temperature
A		°F
B		°F
Drying Time
A		hr
B		hr
Rear Temperature		°F
Middle Temperature		°F
Front Temperature		°F
Nozzle Temperature		°F
Mold Temperature		°F
Injection Pressure		psi
Injection Rate
Screw Speed		rpm

Notes

¹Typical properties: these are not to be construed as specifications.

Reny® 2502AH

Polyarylamide

Glass\Mineral, 20%

Supplied by Mitsubishi Engineering-Plastics Corp