IDES Prospector Already have an account? Login Here

IDES

Adiprene® L-167(MBCA CURED)

Polyurethane (Polyether, TDI)

Supplied by Chemtura

The technical datasheet with complete property values for Adiprene® L-167(MBCA CURED) is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Features 
  • Good Abrasion Resistance
  • Good Tear Strength
  • Good Toughness
  • Low to No Outgassing
  • Resilient
  • Room Temperature Vulcanizing
Uses 
  • Industrial Castings
  • Machine/Mechanical Parts
  • Wheels
Forms 
  • Liquid
Processing Method 
  • Casting
  • Coating
  • Compression Molding
  • Liquid Injection Molding (LIM)
  
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Molding Shrinkage - Flow
in/in
 ASTM D955
Mechanical
Nominal Value
Unit
Test Method
Flexural Modulus
psi
 ASTM D790
Elastomers
Nominal Value
Unit
Test Method
Tensile Stress
     ASTM D412
100% Strain
psi
  
300% Strain
psi
  
Tensile Strength (Yield)
psi
 ASTM D412
Tensile Elongation (Break)
%
 ASTM D412
Tear Strength
      
--
lbf/in
 ASTM D624
Split
lbf/in
 ASTM D470
Compression Set
%
 ASTM D395
Clash-Berg Modulus (75°F)
psi
 ASTM D1043
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact
ft·lb/in
 ASTM D256
Hardness
Nominal Value
Unit
Test Method
Durometer Hardness
     ASTM D2240
Shore A
 
  
Shore D
 
  
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load (66 psi, Unannealed)
°F
 ASTM D648
Brittleness Temperature
°F
 ASTM D746
CLTE - Flow
in/in/°F
 ASTM D696
Thermal Conductivity
Btu·in/hr/ft²/°F
 ASTM C177
Electrical
Nominal Value
Unit
Test Method
Volume Resistivity
ohm·cm
 ASTM D257
Dielectric Constant
     ASTM D150
100 Hz
 
  
100 kHz
 
  
Dissipation Factor
     ASTM D150
100 Hz
 
  
100 kHz
 
  
Thermoset
Nominal Value
Unit
Test Method
Thermoset Components
      
Hardener
 
  
Resin
 
  
Pot Life (185°F)
min
  
Demold Time
      
158°F
min
  
212°F
min
  
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Adiprene® L-167, Adiprene L 167, Adiprene® L-167(MBCA CURED), Adiprene L167MBCA CURED, Adiprene® , Adiprene, AdipreneL167MBCACURED, L-167, L 167, L 167 MBCA CURED, L-167(MBCA CURED), L167MBCA CURED, L:167(MBCA CURED), L:167, L/167(MBCA CURED), L/167, L+167(MBCA CURED), L+167, L_167(MBCA CURED), L_167, L 167(MBCA CURED), L167, 167MBCA, MBCACURED, L167MBCACURED, L_167MBCA CURED, L 167MBCA CURED, Polyurethane, L_167MBCACURED, Polyurethane (Polyether, TDI), Polyurethane Polyether TDI, PUR-Ether/TDI, PUREtherTDI, PUR-Ether:TDI, PUR-Ether+TDI, PUR-Ether-TDI, PUR-Ether_TDI, PUR-Ether TDI, PUR:Ether/TDI, PUR/Ether/TDI, PUR+Ether/TDI, PUR_Ether/TDI, PUR Ether/TDI, PUR, Chemtura, PolyurethanePolyetherTDI, PUREther_TDI, PUREther TDI, PUR_EtherTDI, PUR EtherTDI, 167L
Features
Features may also be described by the following terms: Good Abrasion Resistance, Abrasion Resistant, Low Outgassing, Good Tear Strength, Good Toughness, Tough, Room Temperature Vulcanizing, RTV.
Uses
Uses may also be described by the following terms: Machine Parts, Mechanical Parts, Machine/Mechanical Parts.
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.