IDES Prospector Already have an account? Login Here

IDES

Luvocom® 1/GK/30/TF/13/SI/2

Polyamide 66

Glass Bead, 30%

Supplied by Lehmann & Voss & Co.

The technical datasheet with complete property values for Luvocom® 1/GK/30/TF/13/SI/2 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
  • Asia Pacific
  • Central America
  • Europe
  • Latin America
  • North America
  • South America
Filler / Reinforcement 
  • Glass Bead, 30% Filler by Weight
Additive 
  • Heat Stabilizer
  • PTFE Lubricant (13%)
  • Silicone Lubricant (2%)
Features 
  • Good Wear Resistance
  • Heat Stabilized
  • Low Friction
  • Low Warpage
  
Uses 
  • Automotive Applications
  • Bearings
  • Business Equipment
  • Engineering Parts
  • Gears
  • Switches
  • Textile Applications
Appearance 
  • Beige
  • Natural Color
  
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Molding Shrinkage
%
 DIN 16901
Water Absorption (73°F, 24 hr)
%
  
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ISO 527-2
Tensile Stress (Break)
psi
 ISO 527-2
Tensile Strain (Yield)
%
 ISO 527-2
Flexural Modulus
psi
 ISO 178
Flexural Strength
psi
 ISO 178
Coefficient of Friction
      
vs. Itself - Dynamic
 
  
vs. Itself - Static
 
  
Flexural Strain
%
 ISO 178
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength (73°F)
ft·lb/in²
 ISO 179/1eA
Charpy Unnotched Impact Strength
     ISO 179/1fU
-22°F
ft·lb/in²
  
73°F
ft·lb/in²
  
Thermal
Nominal Value
Unit
Test Method
Maximum Use Temperature - Short Term
°F
  
Vicat Softening Temperature
°F
 ISO 306/A
CLTE - Flow
in/in/°F
 DIN 53752
Thermal Conductivity
Btu·in/hr/ft²/°F
 DIN 52612
Continuous Use Temperature
°F
 UL 746B
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity
ohm
 IEC 60093
Insulation Resistance
ohm
 IEC 60167
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Luvocom® 1/GK/30/TF/13/SI/2, Luvocom 1GK30TF13SI2, Luvocom® , Luvocom, Luvocom1GK30TF13SI2, 1/GK/30/TF/13/SI/2, 1GK30TF13SI2, 1:GK:30:TF:13:SI:2, 1+GK+30+TF+13+SI+2, 1-GK-30-TF-13-SI-2, 1_GK_30_TF_13_SI_2, 1 GK 30 TF 13 SI 2, 1GK, GK30, 30TF, TF13, 13SI, SI2, Polyamide 66, Nylon 66, Polyamide, Nylon, pa66, Lehmann & Voss, Polyamide66, Nylon66, GK1
Generic Name
Generic Name may also be described by the following terms: PA66.
Features
Features may also be described by the following terms: Low Friction, Low Warpage, Low Warp, Good Wear Resistance, Wear Resistant, Heat Stabilized, Heat-ageing Stabilized, Heat Ageing Stabilized, Heat-aging Stabilized, Heat Aging Stabilized.
Uses
Uses may also be described by the following terms: Business Equipment, Business Machines, Automotive Applications, Automotive Sector, Engineering Parts.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Nozzle Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Injection Notes
Drying conditions listed are for a dehumidifying dryer.
Vacuum Dryer Conditions:
  • Drying Temperature: 105°C
  • Drying Time: 4 to 6 hr
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.