IDES Prospector Already have an account? Login Here

IDES

Luvocom® 1/AR/5/NT

Polyamide 66

Aramid Fiber, 5.0%

Supplied by Lehmann & Voss & Co.

The technical datasheet with complete property values for Luvocom® 1/AR/5/NT is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
  • Asia Pacific
  • Central America
  • Europe
  • Latin America
  • North America
  • South America
Filler / Reinforcement 
  • Aramid Fiber, 5.0% Filler by Weight
Features 
  • Good Wear Resistance
  • Low Warpage
  
Uses 
  • Automotive Applications
  • Business Equipment
  • Cams
  • Engineering Parts
  • Textile Applications
Appearance 
  • Natural Color
  • Yellow
  
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Molding Shrinkage
%
 DIN 16901
Water Absorption (73°F, 24 hr)
%
  
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ISO 527-2
Tensile Stress (Break)
psi
 ISO 527-2
Tensile Strain (Yield)
%
 ISO 527-2
Flexural Modulus
psi
 ISO 178
Flexural Strength
psi
 ISO 178
Flexural Strain
%
 ISO 178
Impact
Nominal Value
Unit
Test Method
Charpy Unnotched Impact Strength (73°F)
ft·lb/in²
 ISO 179/1fU
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature (264 psi, Unannealed)
°F
 ISO 75-2/A
Maximum Use Temperature - Short Term
°F
  
Continuous Use Temperature
°F
 UL 746B
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity
ohm
 IEC 60093
Insulation Resistance
ohm
 IEC 60167
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Luvocom® 1/AR/5/NT, Luvocom 1AR5NT, Luvocom® , Luvocom, Luvocom1AR5NT, 1/AR/5/NT, 1AR5NT, 1:AR:5:NT, 1+AR+5+NT, 1-AR-5-NT, 1_AR_5_NT, 1 AR 5 NT, 1AR, AR5, 5NT, Polyamide 66, Nylon 66, Polyamide, Nylon, pa66, Lehmann & Voss, Polyamide66, Nylon66, AR1
Generic Name
Generic Name may also be described by the following terms: PA66.
Features
Features may also be described by the following terms: Low Warpage, Low Warp, Good Wear Resistance, Wear Resistant.
Uses
Uses may also be described by the following terms: Business Equipment, Business Machines, Automotive Applications, Automotive Sector, Engineering Parts.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Nozzle Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Injection Notes
Drying conditions listed are for a dehumidifying dryer.
Vacuum Dryer Conditions:
  • Drying Temperature: 105°C
  • Drying Time: 4 to 6 hr
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.