Hostaform® C 13031 LS Ticona Acetal (POM) Copolymer

Product Description

Chemical abbreviation according to ISO 1043-1: POM
Molding compound ISO 9988- POM-K, M-GNR, 04-002

POM copolymer

Easy flowing Injection molding type like C 13021, but with higher strength, rigidity and hardness over the entire permissible temperature range for HOSTAFORM good chemical resistance to solvents, fuel and strong alkalis as well as good hydrolysis resistance high resistance to thermal and oxidative degradation. With UV Additives

Burning rate ISO 3795 and FMVSS 302 < 75 mm/min for a thickness more than 1 mm.

Ranges of applications: For molded parts with higher requirements to strength, rigidity und hardness,

FMVSS = Federal Motor Vehicle Safety Standard (USA)

General

Material Status

Commercial: Active

Availability

Africa & Middle East

Asia Pacific

Europe

Latin America

North America

South America

Additive

UV Stabilizer

Features

Alkali Resistant

Copolymer

Fuel Resistant

Good Chemical Resistance

Good Flow

Good UV Resistance

High Hardness

High Rigidity

High Strength

Hydrolysis Resistant

Oxidation Resistant

Solvent Resistant

Agency Ratings

RoHS Compliance

Processing Method

Injection Molding

Resin ID (ISO 1043)

Physical	Nominal Value	Unit	Test Method
Density		g/cm³	ISO 1183
Melt Volume-Flow Rate (MVR) (190°C/2.16 kg)		in³/10min	ISO 1133
Molding Shrinkage			ISO 294-4
Across Flow		%
Flow		%
Water Absorption (Saturation, 73°F)		%	ISO 62
Mechanical	Nominal Value	Unit	Test Method
Tensile Modulus		psi	ISO 527-2/1A/1
Tensile Stress (Yield)		psi	ISO 527-2/1A/50
Tensile Strain (Yield)		%	ISO 527-2/1A/50
Nominal Tensile Strain at Break		%	ISO 527-2/1A/50
Tensile Creep Modulus			ISO 899-1
1 hr		psi
1000 hr		psi
Flexural Modulus (73°F)		psi	ISO 178
Impact	Nominal Value	Unit	Test Method
Charpy Notched Impact Strength			ISO 179/1eA
-22°F		ft·lb/in²
73°F		ft·lb/in²
Charpy Unnotched Impact Strength			ISO 179/1eU
-22°F		ft·lb/in²
73°F		ft·lb/in²
Thermal	Nominal Value	Unit	Test Method
Heat Deflection Temperature (264 psi, Unannealed)		°F	ISO 75-2/A
Vicat Softening Temperature		°F	ISO 306/B50
Melting Temperature²		°F	ISO 11357-3
CLTE - Flow		in/in/°F	ISO 11359-2
Electrical	Nominal Value	Unit	Test Method
Surface Resistivity		ohm	IEC 60093
Volume Resistivity		ohm·cm	IEC 60093
Relative Permittivity			IEC 60250
100 Hz
1 MHz
Dissipation Factor			IEC 60250
100 Hz
1 MHz
Comparative Tracking Index		V	IEC 60112
Electric Strength		V/mil	IEC 60243-1
Additional Information	Nominal Value	Unit	Test Method
ISO Type			ISO 9988-1
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Hostaform® C 13031 LS, Hostaform C 13031 LS, Hostaform® , Hostaform, HostaformC13031LS, C 13031 LS, C13031, 13031LS, C13031LS, Acetal Copolymer, Acetal Copolymer, Acetal (POM) Copolymer, Acetal POM Copolymer, Acetal, pom, Ticona, AcetalPOMCopolymer, 13031C
Features
Features may also be described by the following terms: High Hardness, Hard, High Rigidity, High Strength, Good Chemical Resistance, Chemical Resistant, Good Flow, Good UV Resistance, UV Resistant, Ultraviolet Resistant, Ultraviolet Light Resistant.
Agency Ratings
This plastic material has 3 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): EU (1), FDA (1), BgVV (1).

Injection	Nominal Value	Unit
Processing (Melt) Temp		°F
Mold Temperature		°F
Screw L/D Ratio
Injection Notes
Standard injection moulding machines with three phase (15 to 25 D) plasticating screws will fit.

Notes

¹Typical properties: these are not to be construed as specifications.

²10°C/min

Hostaform® C 13031 LS

Acetal (POM) Copolymer

Supplied by Ticona