IDES Prospector Already have an account? Login Here

IDES

LNP* Konduit* PX08322

Polyamide 6

Mineral Filler

Supplied by SABIC Innovative Plastics

The technical datasheet with complete property values for LNP* Konduit* PX08322 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Thermally conductive mineral filled PA6 FR compound, with through-plane and in-plane thermal conductivity of 2.1 W/(m*K) and 8.1 W/(m*K) respectively, conforming to ASTM E 1461 test standard.

Also known as: LNP* Konduit* Compound PX08322
Product reorder name: PX08322
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Filler / Reinforcement 
  • Mineral Filler
Features 
  • Flame Retardant
  • Thermally Conductive
  
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Melt Mass-Flow Rate (MFR) (285°C/6.7 kg)
g/10 min
 ASTM D1238
Molding Shrinkage
     ASTM D955
Flow: 24 hr
in/in
  
Across Flow: 24 hr
in/in
  
Water Absorption
      
73°F, 24 hr
%
 Internal Method
Equilibrium, 73°F, 50% RH
%
 ISO 62
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus 2
psi
 ASTM D638
Tensile Strength 3 (Break)
psi
 ASTM D638
Tensile Elongation 3 (Break)
%
 ASTM D638
Flexural Modulus 4 (1.97 in Span)
psi
 ASTM D790
Flexural Strength 4 (Break, 1.97 in Span)
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact (73°F)
ft·lb/in
 ASTM D256
Unnotched Izod Impact (73°F)
ft·lb/in
 ASTM D4812
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load (264 psi, Unannealed, 0.252 in)
°F
 ASTM D648
CLTE
     ASTM E831
Flow: -40 to 104°F
in/in/°F
  
Flow: 104 to 248°F
in/in/°F
  
Transverse: -40 to 104°F
in/in/°F
  
Transverse: 104 to 248°F
in/in/°F
  
Specific Heat
Btu/lb/°F
 ASTM C351
Thermal Conductivity
Btu·in/hr/ft²/°F
 ASTM E1530
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity
ohm
 ASTM D257
Dielectric Strength (0.0394 in, in Oil)
V/mil
 ASTM D149
Dielectric Constant
     ASTM D150
50 Hz
 
  
60 Hz
 
  
1 MHz
 
  
Dissipation Factor
     ASTM D150
50 Hz
 
  
60 Hz
 
  
1 MHz
 
  
Comparative Tracking Index
V
 IEC 60112
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL (0.0472 in)
 
 UL 94
Glow Wire Ignition Temperature (0.0394 in)
°F
 IEC 60695-2-13
UL
Nominal Value
Unit
Test Method
Hot-wire Ignition (HWI) (PLC)
 
 UL 746
High Amp Arc Ignition (HAI) (PLC)
 
 UL 746
Related Terminology
This supplier and product may also be known by these terms: GE Plastics, LNP Engineering Plastics, GE Polymerland

Product names can be difficult to match. You may have searched any one of these terms to find this product: LNP* Konduit* PX08322, LNP Konduit PX08322, LNP* Konduit* , LNP Konduit, LNPKonduitPX08322, LNPKonduit, PX 08322, PX08322, Polyamide 6, Nylon 6, Polyamide, Nylon, pa6, SABIC IP, Polyamide6, Nylon6, 08322PX
Generic Name
Generic Name may also be described by the following terms: PA6.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Nozzle Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Back Pressure
psi
  
Screw Speed
rpm
  
Notes
1Typical properties: these are not to be construed as specifications.
22.0 in/min
3Type I, 0.20 in/min
40.051 in/min
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.