IDES Prospector Already have an account? Login Here

IDES

ASTALAC™ ABS MGF20E

Acrylonitrile Butadiene Styrene

Glass Fiber Reinforcement, 20%

Supplied by Marplex Australia Pty. Ltd.

The technical datasheet with complete property values for ASTALAC™ ABS MGF20E is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
ASTALAC™ ABS MGF20E is a 20% short fibre length glass filled ABS grade designed for extrusion or moulding into thick sections. This grade features improved rigidity & tensile strength compared to standard ABS extrusion grades, together with a reduced thermal expansion coefficient. These properties are preliminary only, pending full manufacturing runs.

Note: The letters "UV" indicate additional UV stabilisation has been added [ ie: ASTALAC™ ABS MGF20EUV ].
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
  • North America
  • South America
Filler / Reinforcement 
  • Glass Fiber Reinforcement, 20% Filler by Weight
Features 
  • Good Stiffness
  • Good Toughness
  
Uses 
  • Thick-walled Parts
Processing Method 
  • Extrusion
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Melt Mass-Flow Rate (MFR) (220°C/10.0 kg)
g/10 min
 ASTM D1238
Molding Shrinkage - Flow (0.118 in)
in/in
 ASTM D955
Water Absorption (24 hr)
%
 ASTM D570
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength 2 (0.126 in)
psi
 ASTM D638
Tensile Elongation 2 (Break, 0.126 in)
%
 ASTM D638
Flexural Modulus 3 (0.126 in)
psi
 ASTM D790
Flexural Strength 3 (0.126 in)
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact (0.126 in)
ft·lb/in
 ASTM D256
Hardness
Nominal Value
Unit
Test Method
Rockwell Hardness (R-Scale)
 
 ASTM D785
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load
     ASTM D648
264 psi, Unannealed, 0.126 in
°F
  
264 psi, Unannealed, 0.252 in
°F
  
264 psi, Unannealed, 0.500 in
°F
  
Vicat Softening Temperature
°F
 ASTM D1525 4
CLTE - Flow
in/in/°F
 ASTM D696
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL (0.0630 in)
 
 UL 94
Glow Wire Ignition Temperature (0.0630 in)
°F
 AS/NZS 60695.2.12
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: ASTALAC™ ABS MGF20E, ASTALAC ABS MGF20E, ASTALAC™ , ASTALAC, ASTALACABSMGF20E, ABS MGF 20 E, ABS MGF20E, ABSMGF, MGF20, 20E, ABSMGF20E, Acrylonitrile Butadiene Styrene, ABS, Marplex, AcrylonitrileButadieneStyrene, MGFABS
Features
Features may also be described by the following terms: Good Stiffness, Good Toughness, Tough.
Uses
Uses may also be described by the following terms: Thick-walled Parts, Thick Walled Parts, Thick-wall Parts, Thick Wall Parts, Thickwall Parts.
Extrusion
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Cylinder Zone 1 Temp.
°F
  
Cylinder Zone 2 Temp.
°F
  
Cylinder Zone 3 Temp.
°F
  
Cylinder Zone 4 Temp.
°F
  
Cylinder Zone 5 Temp.
°F
  
Melt Temperature
°F
  
Die Temperature
°F
  
Take-Off Roll
°F
  
Back Pressure
psi
  
Notes
1Typical properties: these are not to be construed as specifications.
20.20 in/min
30.051 in/min
4Loading 1 (10 N)
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.