IDES Prospector Already have an account? Login Here

IDES

ASTALON™ MB2106

Polycarbonate

Supplied by Marplex Australia Pty. Ltd.

The technical datasheet with complete property values for ASTALON™ MB2106 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
ASTALON™ MB2106 is an alloy of Polycarbonate (PC) and Polyethylene Terephtalate (PET) which is suited to injection moulding applications. Offering an exceptional combination of toughness, heat resistance, chemical resistance, rigidity, UV resistance and and processability, typical applications include automotive exterior door handles, outside use electric pump housings, automotive bumper bars and electrical switch junction boxes.

Note: The letters "U" or "W" indicate UV stabilisation has been added [ ie: ASTALON™ MB2106U ].
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
  • North America
  • South America
Features 
  • Good Chemical Resistance
  • Good Processability
  • Good Stiffness
  • Good Toughness
  • Good UV Resistance
  • Medium Heat Resistance
Uses 
  • Automotive Applications
  • Automotive Bumper
  • Automotive Exterior Parts
  • Electrical/Electronic Applications
  • Handles
  • Housings
  • Pump Parts
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Melt Mass-Flow Rate (MFR) (300°C/1.2 kg)
g/10 min
 ASTM D1238
Molding Shrinkage - Flow (0.118 in)
in/in
 ASTM D955
Water Absorption (24 hr)
%
 ASTM D570
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength 2 (0.126 in)
psi
 ASTM D638
Tensile Elongation 2 (Break, 0.126 in)
%
 ASTM D638
Flexural Modulus 3 (0.252 in)
psi
 ASTM D790
Flexural Strength 3 (0.252 in)
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact (0.126 in)
ft·lb/in
 ASTM D256
Gardner Impact (0.126 in)
in·lb
 ASTM D3029
Hardness
Nominal Value
Unit
Test Method
Rockwell Hardness (R-Scale)
 
 ASTM D785
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load
     ASTM D648
66 psi, Unannealed, 0.252 in
°F
  
264 psi, Unannealed, 0.252 in
°F
  
CLTE - Flow
in/in/°F
 ASTM D696
Electrical
Nominal Value
Unit
Test Method
Volume Resistivity
ohm·cm
 ASTM D257
Dielectric Constant
 
 ASTM D150
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL (0.0630 in)
 
 UL 94
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: ASTALON™ MB2106, ASTALON MB2106, ASTALON™ , ASTALON, ASTALONMB2106, MB 2106, MB2106, Polycarbonate, PC, Marplex, 2106MB
Features
Features may also be described by the following terms: Good Toughness, Tough, Medium Heat Resistance, Good Chemical Resistance, Chemical Resistant, Good Stiffness, Good UV Resistance, UV Resistant, Ultraviolet Resistant, Ultraviolet Light Resistant, Good Processability, Easy Processing.
Uses
Uses may also be described by the following terms: Automotive Applications, Automotive Sector, Housings, Housing, Automotive Bumper, Automotive Bumpers, Electrical Applications, Electronic Applications, Electrical/Electronic Applications, Electrical Sector.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Injection Pressure
psi
  
Injection Rate
 
  
Back Pressure
psi
  
Screw Speed
rpm
  
Clamp Tonnage
tons/in²
  
Notes
1Typical properties: these are not to be construed as specifications.
20.79 in/min
30.11 in/min
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.