IDES Prospector Already have an account? Login Here

IDES

ASTATAL™ F20

Acetal (POM) Homopolymer

Supplied by Marplex Australia Pty. Ltd.

The technical datasheet with complete property values for ASTATAL™ F20 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
ASTATAL™ F2001 / F2002 / F2003 are the standard medium viscosity (medium melt flow) grades in the ASTATAL™ Polyacetal range and are suited to general purpose injection moulding applications. Offering an exceptional combination of processability, rigidity, frictional wear, heat and chemical resistance, typical applications include mechanical clips, lock linkages and automotive petrol caps.

Note: [ No mould release = 01 ] / [ Standard mould release = 02 ] / [ Low mould deposit = 03 ].

Note: The letters "UV" or "W" indicate UV stabilisation has been added [ ie: ASTATAL™ F2003W ].
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
  • North America
  • South America
Features 
  • General Purpose
  • Good Chemical Resistance
  • Good Processability
  • Good Wear Resistance
  • Medium Flow
  • Medium Heat Resistance
  • Medium Rigidity
  • Medium Viscosity
Uses 
  • Automotive Applications
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)
g/10 min
 ASTM D1238
Molding Shrinkage - Flow (0.118 in)
in/in
 ASTM D955
Water Absorption (24 hr)
%
 ASTM D570
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength 2 (0.126 in)
psi
 ASTM D638
Tensile Elongation 2 (Break, 0.126 in)
%
 ASTM D638
Flexural Modulus 3 (0.252 in)
psi
 ASTM D790
Flexural Strength 3 (0.252 in)
psi
 ASTM D790
Shear Strength (0.0787 in)
psi
 ASTM D732
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact (0.126 in)
ft·lb/in
 ASTM D256
Tensile Impact Strength (0.0630 in)
ft·lb/in²
 ASTM D1822
Hardness
Nominal Value
Unit
Test Method
Rockwell Hardness (M-Scale)
 
 ASTM D785
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load
     ASTM D648
66 psi, Unannealed, 0.252 in
°F
  
264 psi, Unannealed, 0.252 in
°F
  
Melting Temperature
°F
 DSC
CLTE - Flow
in/in/°F
 ASTM D696
Electrical
Nominal Value
Unit
Test Method
Volume Resistivity
ohm·cm
 ASTM D257
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL (0.0315 in)
 
 UL 94
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: ASTATAL™ F20, ASTATAL F20, ASTATAL™ , ASTATAL, ASTATALF20, F 20, F20, Acetal Homopolymer, Acetal Homopolymer, Acetal (POM) Homopolymer, Acetal POM Homopolymer, Acetal, pom, Marplex, AcetalPOMHomopolymer, 20F
Features
Features may also be described by the following terms: Medium Viscosity, Medium Flow, Medium Melt, Medium MFI, Good Processability, Easy Processing, Medium Rigidity, Good Rigidity, Good Wear Resistance, Wear Resistant, Medium Heat Resistance, Good Chemical Resistance, Chemical Resistant.
Uses
Uses may also be described by the following terms: Automotive Applications, Automotive Sector.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Injection Pressure
psi
  
Injection Rate
 
  
Back Pressure
psi
  
Screw Speed
rpm
  
Clamp Tonnage
tons/in²
  
Notes
1Typical properties: these are not to be construed as specifications.
20.79 in/min
30.11 in/min
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.