IDES Prospector Already have an account? Login Here

IDES

SABIC® PPcompound 2606 Provisional

Compounded Polypropylene

Mineral Filler

Supplied by Saudi Basic Industries Corporation (SABIC)

The technical datasheet with complete property values for SABIC® PPcompound 2606 Provisional is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Description:
SABIC® PPcompound 2606 is a mineral filled modified polypropylene. Typical material properties include an excellent impact stiffness balance with a low density. This material was optimized for low smell, low emission and good scratch resistance. Typical applications include automotive interior parts such as trims and dashboards.

SABIC® PPcompound 2606 is a designated automotive grade.

IMDS ID: 138505251
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Filler / Reinforcement 
  • Mineral Filler
Features 
  • Low Density
  • Low Emissions
  • Low to No Odor
  • Scratch Resistant
  • Ultra High Impact Resistance
Uses 
  • Automotive Applications
  • Automotive Instrument Panel
  • Automotive Interior Parts
  • Automotive Interior Trim
  
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Melt Mass-Flow Rate (MFR) (230°C/2.16 kg)
g/10 min
 ISO 1133
Molding Shrinkage 2 (24 hr)
%
 Internal Method
Mechanical
Nominal Value
Unit
Test Method
Tensile Stress
     ISO 527-2/50
Yield, 0.126 in, Injection Molded
psi
  
Break, 0.126 in, Injection Molded
psi
  
Tensile Strain (Break, 0.126 in, Injection Molded)
%
 ISO 527-2/50
Flexural Modulus 3 (Injection Molded)
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength (73°F, Injection Molded)
 
 ISO 179
Charpy Unnotched Impact Strength (-40°F, Injection Molded)
 
 ISO 179
Notched Izod Impact Strength
     ISO 180/4A
-4°F, Injection Molded
ft·lb/in²
  
32°F, Injection Molded
ft·lb/in²
  
73°F, Injection Molded
 
  
Hardness
Nominal Value
Unit
Test Method
Shore Hardness (Shore D, Injection Molded)
 
 ISO 868
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature (66 psi, Unannealed)
°F
 ISO 75-2/B
Vicat Softening Temperature
°F
 ISO 306/A
CLTE - Flow
     ASTM D696
-22 to 86°F
in/in/°F
  
73 to 176°F
in/in/°F
  
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: SABIC® PPcompound 2606 Provisional, SABIC PPcompound 2606 Provisional, SABIC® PPcompound , SABIC PPcompound, SABICPPcompound2606Provisional, SABICPPcompound, PPcompound 2606 Provisional, PPcompound2606 Provisional, PPcompound2606, PPcompound, PPcompound2606Provisional, 2606 Provisional, 2606Provisional, Polypropylene, Compounded, Polypropylene Compounded, TPO, Polypropylene, PP, SABIC, PolypropyleneCompounded, Provisional2606, 2606PPcompound
Features
Features may also be described by the following terms: Low Density, Low Specific Gravity, Low Emissions, Ultra High Impact Resistance, Low Odor, Scratch Resistant, Resists Scratches.
Uses
Uses may also be described by the following terms: Automotive Applications, Automotive Sector, Automotive Instrument Panel, Automotive Dash Board.
Notes
1Typical properties: these are not to be construed as specifications.
2?Injection Molded
3Method I (3 point load)
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.