IDES Prospector Already have an account? Login Here

IDES

LNP* Konduit* PX11311

Polyamide 6

Mineral Filler

Supplied by SABIC Innovative Plastics Asia Pacific

The technical datasheet with complete property values for LNP* Konduit* PX11311 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Thermally conductive mineral filled PA6 FR compound, with through-plane thermal conductivity of 1.4 W/(m*K) measured with 3mm thick specimen, conforming to ASTM E 1461 test standard.

Also known as: LNP* Konduit* Compound PX11311
Product reorder name: PX11311
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
Filler / Reinforcement 
  • Mineral Filler
Features 
  • Flame Retardant
  • Thermally Conductive
  
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ASTM D792
Melt Volume-Flow Rate (MVR) (300°C/10.0 kg)
in³/10min
 ISO 1133
Molding Shrinkage
     ASTM D955
Flow: 24 hr
in/in
  
Across Flow: 24 hr
in/in
  
Water Absorption
      
73°F, 24 hr
%
 Internal Method
Equilibrium, 73°F, 50% RH
%
 ISO 62
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus 2
psi
 ASTM D638
Tensile Strength 3 (Break)
psi
 ASTM D638
Tensile Elongation 3 (Break)
%
 ASTM D638
Flexural Modulus 4 (1.97 in Span)
psi
 ASTM D790
Flexural Strength 4 (Break, 1.97 in Span)
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact (73°F)
ft·lb/in
 ASTM D256
Unnotched Izod Impact (73°F)
ft·lb/in
 ASTM D4812
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load (264 psi, Unannealed, 0.252 in)
°F
 ASTM D648
CLTE
     ASTM E831
Flow: -40 to 104°F
in/in/°F
  
Flow: 104 to 248°F
in/in/°F
  
Transverse: -40 to 104°F
in/in/°F
  
Transverse: 104 to 248°F
in/in/°F
  
Specific Heat
Btu/lb/°F
 ASTM C351
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity
ohm
 ASTM D257
Dielectric Strength (0.0394 in, in Oil)
V/mil
 ASTM D149
Comparative Tracking Index
V
 IEC 60112
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL (0.0394 in)
 
 UL 94
Glow Wire Flammability Index (0.0787 in)
°F
 IEC 60695-2-12
Glow Wire Ignition Temperature
     IEC 60695-2-13
0.0394 in
°F
  
0.118 in
°F
  
UL
Nominal Value
Unit
Test Method
Hot-wire Ignition (HWI) (PLC)
 
 UL 746
High Amp Arc Ignition (HAI) (PLC)
 
 UL 746
Related Terminology
This supplier and product may also be known by these terms: GE Plastics, LNP Engineering Plastics

Product names can be difficult to match. You may have searched any one of these terms to find this product: LNP* Konduit* PX11311, LNP Konduit PX11311, LNP* Konduit* , LNP Konduit, LNPKonduitPX11311, LNPKonduit, PX 11311, PX11311, Polyamide 6, Nylon 6, Polyamide, Nylon, pa6, SABIC IP Asia, Polyamide6, Nylon6, 11311PX
Generic Name
Generic Name may also be described by the following terms: PA6.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Suggested Max Moisture
%
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Back Pressure
psi
  
Screw Speed
rpm
  
Notes
1Typical properties: these are not to be construed as specifications.
20.20 in/min
3Type I, 0.20 in/min
40.051 in/min
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.