Hostaform® C 13031 XAP Ticona Acetal (POM) Copolymer

Product Description

Polyacetal copolymer, reduced emission

Easy flowing Injection molding type like C 13021 XAP, but with higher strength, rigidity and hardness over the entire permissible temperature range for HOSTAFORM; good chemical resistance to solvents, fuel and strong alkalis as well as good hydrolysis resistance; high resistance to thermal and oxidative degradation.

Emissions according to VDA 275 < 10 ppm (natural and colored grades)

Fulfils EG-directive 2002/72/EU as well as the recommendation XXXIII for consumer goods of the BgVV, FDA compliant according to 21 CFR 177.2470

Burning rate ISO 3795 and FMVSS 302 < 100 mm/min for a thickness more than 1 mm.

Ranges of applications: For molded parts with higher requirements to strength, rigidity und hardness, ranges of applications with fuel contact.

General

Material Status

Commercial: Active

Availability

Europe

North America

Features

Alkali Resistant

Copolymer

Fuel Resistant

Good Chemical Resistance

Good Flow

Good Stiffness

Good Strength

High Heat Resistance

Hydrolysis Resistant

Solvent Resistant

Agency Ratings

RoHS Compliance

Processing Method

Injection Molding

Physical	Nominal Value	Unit	Test Method
Density		g/cm³	ISO 1183
Melt Volume-Flow Rate (MVR) (190°C/2.16 kg)		in³/10min	ISO 1133
Molding Shrinkage			ISO 294-4
Across Flow		%
Flow		%
Water Absorption (Saturation, 73°F)		%	ISO 62
Mechanical	Nominal Value	Unit	Test Method
Tensile Modulus		psi	ISO 527-2/1A/1
Tensile Stress (Yield)		psi	ISO 527-2/1A/50
Tensile Strain (Yield)		%	ISO 527-2/1A/50
Nominal Tensile Strain at Break		%	ISO 527-2/1A/50
Tensile Creep Modulus			ISO 899-1
1 hr		psi
1000 hr		psi
Flexural Modulus (73°F)		psi	ISO 178
Impact	Nominal Value	Unit	Test Method
Charpy Notched Impact Strength			ISO 179/1eA
-22°F		ft·lb/in²
73°F		ft·lb/in²
Charpy Unnotched Impact Strength			ISO 179/1eU
-22°F		ft·lb/in²
73°F		ft·lb/in²
Thermal	Nominal Value	Unit	Test Method
Heat Deflection Temperature (264 psi, Unannealed)		°F	ISO 75-2/A
Vicat Softening Temperature		°F	ISO 306/B50
Melting Temperature²		°F	ISO 11357-3
CLTE - Flow		in/in/°F	ISO 11359-2
Electrical	Nominal Value	Unit	Test Method
Surface Resistivity		ohm	IEC 60093
Volume Resistivity		ohm·cm	IEC 60093
Relative Permittivity			IEC 60250
100 Hz
1 MHz
Dissipation Factor			IEC 60250
100 Hz
1 MHz
Comparative Tracking Index		V	IEC 60112
Electric Strength		V/mil	IEC 60243-1
Flammability	Nominal Value	Unit	Test Method
Burning Rate (0.0394 in)		in/min	ISO 3795
Additional Information	Nominal Value	Unit	Test Method
Emission		ppm	VDA 275
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Hostaform® C 13031 XAP, Hostaform C 13031 XAP, Hostaform® , Hostaform, HostaformC13031XAP, C 13031 XAP, C13031, 13031XAP, C13031XAP, Acetal Copolymer, Acetal Copolymer, Acetal (POM) Copolymer, Acetal POM Copolymer, Acetal, pom, Ticona, AcetalPOMCopolymer, 13031C
Features
Features may also be described by the following terms: Good Flow, Good Chemical Resistance, Chemical Resistant, Good Stiffness, Good Strength, High Heat Resistance.
Agency Ratings
This plastic material has 3 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): EU (1), FDA (1), BgVV (1).

Notes

¹Typical properties: these are not to be construed as specifications.

²10°C/min

Hostaform® C 13031 XAP

Acetal (POM) Copolymer

Supplied by Ticona