IDES Prospector Already have an account? Login Here

IDES

Hostaform® C 2521 XAP² ™

Acetal (POM) Copolymer

Supplied by Ticona

The technical datasheet with complete property values for Hostaform® C 2521 XAP² ™ is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
POM copolymer
Stiff-flowing type for injection molding and extrusion with high impact toughness and good tracking resistance over a high range of temperature; good chemical resistance to solvents, fuel and strong alkalis as well as good hydrolysis resistance; high resistance to thermal and oxidative degradation.
With reduced emissions especially for automotive interior application.

Burning rate according to FMVSS 302 < 100 mm/min (1 mm thickness)

Emission according to VDA 275 < 5 mg/kg (natural grades)
Emission according to VDA 275 < 5 mg/kg (colored grades)

Preliminary Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
  • North America
  
Features 
  • Alkali Resistant
  • Copolymer
  • Fuel Resistant
  • Good Chemical Resistance
  • High Heat Resistance
  • High Impact Resistance
  • Hydrolysis Resistant
  • Solvent Resistant
  • Tracking Resistant
RoHS Compliance 
Processing Method 
  • Extrusion
  • Injection Molding
  
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Melt Volume-Flow Rate (MVR) (190°C/2.16 kg)
in³/10min
 ISO 1133
Water Absorption (Saturation, 73°F)
%
 ISO 62
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ISO 527-2/1A/1
Tensile Stress (Yield)
psi
 ISO 527-2/1A/50
Tensile Strain (Yield)
%
 ISO 527-2/1A/50
Nominal Tensile Strain at Break
%
 ISO 527-2/1A/50
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength
     ISO 179/1eA
-22°F
ft·lb/in²
  
73°F
ft·lb/in²
  
Charpy Unnotched Impact Strength
     ISO 179/1eU
-22°F
ft·lb/in²
  
73°F, Partial Break
ft·lb/in²
  
Thermal
Nominal Value
Unit
Test Method
Melting Temperature 2
°F
 ISO 11357-3
CLTE
     ISO 11359-2
Flow
in/in/°F
  
Transverse
in/in/°F
  
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity
ohm
 IEC 60093
Volume Resistivity
ohm·cm
 IEC 60093
Relative Permittivity
     IEC 60250
100 Hz
 
  
1 MHz
 
  
Dissipation Factor
     IEC 60250
100 Hz
 
  
1 MHz
 
  
Comparative Tracking Index
V
 IEC 60112
Electric Strength
V/mil
 IEC 60243-1
Fill Analysis
Nominal Value
Unit
Test Method
Melt Density
g/cm³
 Internal Method
Melt Thermal Conductivity
Btu·in/hr/ft²/°F
 Internal Method
Ejection Temperature
°F
  
Specific Heat Capacity of Melt
Btu/lb/°F
 Internal Method
Additional Information
Nominal Value
Unit
Test Method
Emission
mg/kg
 VDA 275
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Hostaform® C 2521 XAP² ™, Hostaform C 2521 XAP, Hostaform® , Hostaform, HostaformC2521XAP, C 2521 XAP² ™, C 2521 XAP, C2521, 2521XAP, C2521XAP, Acetal Copolymer, Acetal Copolymer, Acetal (POM) Copolymer, Acetal POM Copolymer, Acetal, pom, Ticona, AcetalPOMCopolymer, 2521C
Features
Features may also be described by the following terms: High Impact Resistance, Good Chemical Resistance, Chemical Resistant, High Heat Resistance.
Notes
1Typical properties: these are not to be construed as specifications.
210°C/min
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.