IDES Prospector Already have an account? Login Here

IDES

Hostaform® C 9021 AW XAP² ™ LS

Acetal (POM) Copolymer

Supplied by Ticona

The technical datasheet with complete property values for Hostaform® C 9021 AW XAP² ™ LS is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
POM copolymer

Injection molding type like C 9021, with special additive modified; good chemical resistance to solvents, fuel and strong alkalis as well as good hydrolysis resistance; high resistance to thermal and oxidative degradation; good wear properties and low coefficient of friction.
Reduced emission grade. Emissions according to VDA 275 < 5 mg/kg

Burning rate ISO 3795 and FMVSS 302 < 100 mm/min for a thickness more than 1 mm.

Ranges of applications: sliding parts for window lifter.

FMVSS = Federal Motor Vehicle Safety Standard (USA)

Preliminary Data Sheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
  • North America
  
Additive 
  • Unspecified Additive
Features 
  • Alkali Resistant
  • Fuel Resistant
  • Good Chemical Resistance
  • Good Wear Resistance
  • High Heat Resistance
  • Hydrolysis Resistant
  • Low Emissions
  • Low Friction
  • Solvent Resistant
Uses 
  • Automotive Applications
RoHS Compliance 
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Melt Volume-Flow Rate (MVR) (190°C/2.16 kg)
in³/10min
 ISO 1133
Molding Shrinkage
     ISO 294-4
Across Flow
%
  
Flow
%
  
Water Absorption (Saturation, 73°F)
%
 ISO 62
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ISO 527-2/1A/1
Tensile Stress (Yield)
psi
 ISO 527-2/1A/50
Tensile Strain (Yield)
%
 ISO 527-2/1A/50
Nominal Tensile Strain at Break
%
 ISO 527-2/1A/50
Flexural Modulus (73°F)
psi
 ISO 178
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength
     ISO 179/1eA
-22°F
ft·lb/in²
  
73°F
ft·lb/in²
  
Charpy Unnotched Impact Strength
     ISO 179/1eU
-22°F
ft·lb/in²
  
73°F
ft·lb/in²
  
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature (264 psi, Unannealed)
°F
 ISO 75-2/A
Vicat Softening Temperature
°F
 ISO 306/B50
Melting Temperature 2
°F
 ISO 11357-3
CLTE - Flow
in/in/°F
 ISO 11359-2
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity
ohm
 IEC 60093
Volume Resistivity
ohm·cm
 IEC 60093
Relative Permittivity
     IEC 60250
100 Hz
 
  
1 MHz
 
  
Dissipation Factor
     IEC 60250
100 Hz
 
  
1 MHz
 
  
Comparative Tracking Index
V
 IEC 60112
Electric Strength
V/mil
 IEC 60243-1
Flammability
Nominal Value
Unit
Test Method
Burning Rate (0.0394 in)
in/min
 ISO 3795
Additional Information
Nominal Value
Unit
Test Method
Emission
mg/kg
 VDA 275
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Hostaform® C 9021 AW XAP² ™ LS, Hostaform C 9021 AW XAP LS, Hostaform® , Hostaform, HostaformC9021AWXAPLS, C 9021 AW XAP² ™ LS, C 9021 AW XAP LS, C9021, 9021AW, AWXAP, XAPLS, C9021AWXAPLS, Acetal Copolymer, Acetal Copolymer, Acetal (POM) Copolymer, Acetal POM Copolymer, Acetal, pom, Ticona, AcetalPOMCopolymer, 9021C
Features
Features may also be described by the following terms: Good Chemical Resistance, Chemical Resistant, Low Emissions, Low Friction, High Heat Resistance, Good Wear Resistance, Wear Resistant.
Uses
Uses may also be described by the following terms: Automotive Applications, Automotive Sector.
Notes
1Typical properties: these are not to be construed as specifications.
210°C/min
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.