IDES Prospector Already have an account? Login Here

IDES

TAROMID B 280 Z2

Polyamide 6

Supplied by Taro Plast S.p.A.

The technical datasheet with complete property values for TAROMID B 280 Z2 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Additive 
  • Impact Modifier
Features 
  • Good Chemical Resistance
  • Impact Modified
  • Low Temperature Impact Resistance
  • Medium Viscosity
  • Oil Resistant
  • Solvent Resistant
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Molding Shrinkage - Flow
%
 Internal Method
Water Absorption
     ISO 62
73°F, 24 hr
%
  
Saturation, 73°F
%
  
Granule Humidity 2
%
 Internal Method
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ISO 527-2/1
Tensile Stress
     ISO 527-2/50
Yield
psi
  
Break
psi
  
Tensile Strain (Break)
%
 ISO 527-2/50
Flexural Modulus 3
psi
 ISO 178
Flexural Strength 3
psi
 ISO 178
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength (73°F)
ft·lb/in²
 ISO 179/1eA
Charpy Unnotched Impact Strength
     ISO 179/1eU
-13°F
 
  
73°F
 
  
Notched Izod Impact
     ASTM D256
-4°F
ft·lb/in
  
73°F
ft·lb/in
  
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature 4 (264 psi, Unannealed)
°F
 ISO 75-2/A
Vicat Softening Temperature
°F
 ISO 306/B50
Ball Pressure Test (257°F)
 
 IEC 60695-10-2
Melting Temperature
°F
 ISO 11357-3
CLTE - Flow (-22 to 86°F)
in/in/°F
 ISO 11359-2
Electrical
Nominal Value
Unit
Test Method
Volume Resistivity
ohm·cm
 IEC 60093
Dielectric Constant
 
 IEC 60250
Comparative Tracking Index (Solution A)
V
 IEC 60112
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL (0.0630 in)
 
 UL 94
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: TAROMID B 280 Z2 , TAROMID B , TAROMIDB280Z2, TAROMIDB, B 280 Z 2, B280 Z2, B280, 280 Z 2, B280Z2, 280 Z2, 280Z, Z2, 280Z2, Polyamide 6, Nylon 6, Polyamide, Nylon, pa6, Taro Plast, Polyamide6, Nylon6, Z280, 280B
Generic Name
Generic Name may also be described by the following terms: PA6.
Features
Features may also be described by the following terms: Medium Viscosity, Low Temperatuer Impact Resistance, Low Temp Impact Resistance, Good Chemical Resistance, Chemical Resistant.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Injection Rate
 
  
Injection Notes
Pre-heat Temperature: 80 to 100°C
Pre-heat Time: 3 hr
Notes
1Typical properties: these are not to be construed as specifications.
2TARO 002
30.039 in/min
4120°C/hr
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.