IDES Prospector Already have an account? Login Here

IDES

Adiprene® L-315(MBCA CURED)

Polyurethane (Polyether, TDI)

Supplied by Chemtura

The technical datasheet with complete property values for Adiprene® L-315(MBCA CURED) is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Features 
  • General Purpose
  • Good Abrasion Resistance
  • Good Processability
  • Good Stiffness
  • Good Tear Strength
  • Good Toughness
  • Low to No Outgassing
  • Room Temperature Vulcanizing
Uses 
  • Bearings
  • Machine/Mechanical Parts
  • Wheels
Forms 
  • Liquid
Processing Method 
  • Casting
  • Coating
  • Compression Molding
  • Liquid Injection Molding (LIM)
  
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Molding Shrinkage - Flow
in/in
 ASTM D955
Water Absorption (24 hr)
%
 ASTM D570
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ASTM D638
Tensile Strength (Yield)
psi
 ASTM D638
Tensile Elongation (Break)
%
 ASTM D638
Flexural Modulus
psi
 ASTM D790
Compressive Modulus
psi
 ASTM D695
Elastomers
Nominal Value
Unit
Test Method
Tensile Stress (100% Strain)
psi
 ASTM D412
Tensile Strength (Yield)
psi
 ASTM D412
Tensile Elongation (Break)
%
 ASTM D412
Tear Strength (Split)
lbf/in
 ASTM D470
Compression Set (158°F)
%
 ASTM D395
Clash-Berg Modulus (75°F)
psi
 ASTM D1043
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact     ASTM D256
-40°F
ft·lb/in
  
75°F
ft·lb/in
  
Unnotched Izod Impact (75°F)
 
 ASTM D256
Hardness
Nominal Value
Unit
Test Method
Durometer Hardness (Shore D)
 
 ASTM D2240
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load     ASTM D648
66 psi, Unannealed
°F
  
264 psi, Unannealed
°F
  
Brittleness Temperature
°F
 ASTM D746
CLTE - Flow
in/in/°F
 ASTM D696
Electrical
Nominal Value
Unit
Test Method
Volume Resistivity
ohm·cm
 ASTM D257
Dielectric Strength
V/mil
 ASTM D149
Dielectric Constant (1 kHz)
 
 ASTM D150
Dissipation Factor (1 kHz)
 
 ASTM D150
Thermoset
Nominal Value
Unit
Test Method
Thermoset Components      
Hardener
 
  
Resin
 
  
Pot Life (150°F)
min
  
Demold Time (212°F)
min
  
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Adiprene® L-315, Adiprene L 315, Adiprene® L-315(MBCA CURED), Adiprene L315MBCA CURED, Adiprene® , Adiprene, AdipreneL315MBCACURED, L-315, L 315, L 315 MBCA CURED, L-315(MBCA CURED), L315MBCA CURED, L:315(MBCA CURED), L:315, L/315(MBCA CURED), L/315, L+315(MBCA CURED), L+315, L_315(MBCA CURED), L_315, L 315(MBCA CURED), L315, 315MBCA, MBCACURED, L315MBCACURED, L_315MBCA CURED, L 315MBCA CURED, Polyurethane, L_315MBCACURED, Polyurethane (Polyether, TDI), Polyurethane Polyether TDI, PUR-Ether/TDI, PUREtherTDI, PUR-Ether:TDI, PUR-Ether+TDI, PUR-Ether-TDI, PUR-Ether_TDI, PUR-Ether TDI, PUR:Ether/TDI, PUR/Ether/TDI, PUR+Ether/TDI, PUR_Ether/TDI, PUR Ether/TDI, PUR, Chemtura, PolyurethanePolyetherTDI, PUREther_TDI, PUREther TDI, PUR_EtherTDI, PUR EtherTDI, 315L
Features
Features may also be described by the following terms: Good Abrasion Resistance, Abrasion Resistant, Low Outgassing, Good Processability, Easy Processing, Good Stiffness, Good Tear Strength, Good Toughness, Tough, Room Temperature Vulcanizing, RTV.
Uses
Uses may also be described by the following terms: Machine Parts, Mechanical Parts, Machine/Mechanical Parts.
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.