IDES Prospector Already have an account? Login Here

IDES

Clariant PC PC-1100TF15

Polycarbonate

Supplied by Clariant Performance Plastics

The technical datasheet with complete property values for Clariant PC PC-1100TF15 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Additive 
  • PTFE Lubricant (15%)
Features 
  • Good Chemical Resistance
  • Good Colorability
  • Good Corrosion Resistance
  • Good Dimensional Stability
  • Good Processability
  • Good Stiffness
  • Good Toughness
  • Good Wear Resistance
  • High Rigidity
  • High Strength
  • Low Friction
  • Low to No Water Absorption
  • Lubricated
Uses 
  • Cams
  • Gears
  • Metal Replacement
  • Military Applications
  • Sporting Goods
Appearance 
  • Colors Available
  • Natural Color
  
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Molding Shrinkage - Flow (0.125 in)
in/in
 ASTM D955
Water Absorption
     ASTM D570
24 hr
%
  
Saturation
%
  
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength
psi
 ASTM D638
Tensile Elongation (Break)
%
 ASTM D638
Flexural Modulus
psi
 ASTM D790
Flexural Strength
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact (0.125 in)
ft·lb/in
 ASTM D256
Hardness
Nominal Value
Unit
Test Method
Rockwell Hardness (M-Scale)
 
 ASTM D785
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load
     ASTM D648
66 psi, Unannealed
°F
  
264 psi, Unannealed
°F
  
CLTE - Flow
in/in/°F
 ASTM D696
Electrical
Nominal Value
Unit
Test Method
Volume Resistivity
ohm·cm
 ASTM D257
Dielectric Strength
V/mil
 ASTM D149
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL
 
 UL 94
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Clariant PC PC-1100TF15, Clariant PC PC1100TF15, Clariant PC , ClariantPCPC1100TF15, ClariantPC, PCPC 1100 TF 15, PC, PCPC-1100TF15, PCPC1100TF15, PCPC:1100TF15, PCPC/1100TF15, PCPC+1100TF15, PCPC_1100TF15, PCPC 1100TF15, PCPC1100, PCPC, PC 1100 TF 15, PC-1100TF15, PC1100TF15, PC:1100TF15, PC/1100TF15, PC+1100TF15, PC_1100TF15, PC 1100TF15, PC1100, 1100TF, TF15, Polycarbonate, Clariant Perf, 1100PC, 1100PCPC
Features
Features may also be described by the following terms: Good Chemical Resistance, Chemical Resistant, Good Colorability, Good Dimensional Stability, Dimensionally Stable, Good Corrosion Resistance, Corrosion Resistant, High Strength, Low Friction, Good Processability, Easy Processing, High Rigidity, Good Stiffness, Good Toughness, Tough, Good Wear Resistance, Wear Resistant, Low Water Absorption, Low Moisture Absorption, Water Resistant, Moisure Resistant.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Suggested Max Moisture
%
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Processing (Melt) Temp
°F
  
Melt Temperature (Aim)
°F
  
Mold Temperature
°F
  
Injection Rate
 
  
Back Pressure
psi
  
Screw Speed
rpm
  
Cushion
in
  
Injection Notes
The minimum injection pressure required to fill the part should be used for the first stage. The hold pressure should be set between 50% and 75% of the injection pressure.
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.