|
Specific Gravity
|
|
|
ASTM D792 |
|
Melt Mass-Flow Rate (MFR) (337°C/6.6 kg)
|
|
g/10 min
|
ASTM D1238 |
|
Molding Shrinkage - Flow (0.126 in)
|
|
in/in
|
Internal Method |
|
Water Absorption
|
|
|
ASTM D570 |
|
24 hr
|
|
%
|
|
|
Equilibrium, 73°F
|
|
%
|
|
|
Tensile Modulus 2
|
|
psi
|
ASTM D638 |
|
Tensile Strength 3 (Yield)
|
|
psi
|
ASTM D638 |
|
Tensile Elongation 3
|
|
|
ASTM D638 |
|
Yield
|
|
%
|
|
|
Break
|
|
%
|
|
|
Flexural Modulus 4 (3.94 in Span)
|
|
psi
|
ASTM D790 |
|
Flexural Strength 4 (Yield, 3.94 in Span)
|
|
psi
|
ASTM D790 |
|
Taber Abrasion Resistance (1000 Cycles, 1000 g, CS-17 Wheel)
|
|
mg
|
ASTM D1044 |
|
Notched Izod Impact (73°F)
|
|
ft·lb/in
|
ASTM D256 |
|
Unnotched Izod Impact (73°F)
|
|
ft·lb/in
|
ASTM D4812 |
|
Reverse Notch Izod Impact (0.126 in)
|
|
ft·lb/in
|
ASTM D256 |
|
Gardner Impact (73°F)
|
|
in·lb
|
ASTM D3029 |
|
Rockwell Hardness (M-Scale)
|
|
|
ASTM D785 |
|
Deflection Temperature Under Load
|
|
|
ASTM D648 |
|
66 psi, Unannealed, 0.252 in
|
|
°F
|
|
|
264 psi, Unannealed, 0.252 in
|
|
°F
|
|
|
Vicat Softening Temperature
|
|
°F
|
ASTM D1525 5 |
|
CLTE - Flow (-4 to 302°F)
|
|
in/in/°F
|
ASTM E831 |
|
Thermal Conductivity
|
|
Btu·in/hr/ft²/°F
|
ASTM C177 |
|
Volume Resistivity
|
|
ohm·cm
|
ASTM D257 |
|
Dielectric Strength
|
|
|
ASTM D149 |
|
0.0630 in, in Air
|
|
V/mil
|
|
|
0.0630 in, in Oil
|
|
V/mil
|
|
|
Dielectric Constant (1 kHz)
|
|
|
ASTM D150 |
|
Dissipation Factor
|
|
|
ASTM D150 |
|
1 kHz
|
|
|
|
|
2.45 GHz
|
|
|
|
|
Arc Resistance (PLC) 6
|
|
|
ASTM D495 |
|
Oxygen Index
|
|
%
|
ASTM D2863 |
|
NBS Smoke Density - Flaming, Ds, 4 min
|
|
|
ASTM E662 |
|
RTI Str
|
|
°F
|
UL 746 |
|
RTI Imp
|
|
°F
|
UL 746 |
|
RTI Elec
|
|
°F
|
UL 746 |
|
Comparative Tracking Index (CTI) (PLC)
|
|
|
UL 746 |
|
High Voltage Arc Tracking Rate (HVTR) (PLC)
|
|
|
UL 746 |
|
Hot-wire Ignition (HWI) (PLC)
|
|
|
UL 746 |
|
High Amp Arc Ignition (HAI) (PLC)
|
|
|
UL 746 |
|
This supplier and product may also be known by these terms: GE Plastics, LNP Engineering Plastics, GE Polymerland
Product names can be difficult to match. You may have searched any one of these terms to find this product: ULTEM* 1010F Resin, ULTEM 1010F Resin, ULTEM* , ULTEM, ULTEM1010FResin, 1010 F Resin, 1010F Resin, 1010F, FResin, 1010FResin, Polyether Imide, PEI, SABIC IP, PolyetherImide, F1010
|
|
Features may also be described by the following terms: Good Flow.
|
|
This plastic material has approval for 1 automotive specifications from the following agencies (the number in parentheses shows the number of specifications for that agency): FORD (1).
|
|
This plastic material has 4 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): EU (2), FDA (1), NSF (1).
|