IDES Prospector Already have an account? Login Here

IDES

ULTEM* 1110F Resin

Polyether Imide

Supplied by SABIC Innovative Plastics

The technical datasheet with complete property values for ULTEM* 1110F Resin is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Enhanced flow Polyetherimide (Tg 217C). ECO Conforming. US FDA and EU Food Contact compliant, NSF 51 listing. Effective June 2007, this grade will no longer be supported with biocompatibility information and should not be used for medical applications which require biocompatibility. Alternative grade HU1110.
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Features 
  • ECO Compliant
  • Food Contact Acceptable
  • Good Flow
Agency Ratings 
 
Processing Method 
  • Injection Molding
Multi-Point Data 
  • Instrumented Impact (Energy) (ASTM D3763)
  • Instrumented Impact (Load) (ASTM D3763)
  • Pressure-Volume-Temperature (PVT - Zoller Method)
  • Tensile Fatigue
  • Tensile Stress vs. Strain (ASTM D638)
  • Thermal Conductivity vs. Temperature (ASTM E1530)
  • Viscosity vs. Shear Rate (ASTM D3835)
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Melt Mass-Flow Rate (MFR) (337°C/6.6 kg)
g/10 min
 ASTM D1238
Molding Shrinkage - Flow (0.126 in)
in/in
 Internal Method
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus 2
psi
 ASTM D638
Tensile Strength 3 (Yield)
psi
 ASTM D638
Tensile Elongation 3 (Break)
%
 ASTM D638
Flexural Modulus 4 (3.94 in Span)
psi
 ASTM D790
Flexural Strength 4 (Yield, 3.94 in Span)
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Reverse Notch Izod Impact (0.126 in)
ft·lb/in
 ASTM D256
Gardner Impact (73°F)
in·lb
 ASTM D3029
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load (264 psi, Unannealed, 0.252 in)
°F
 ASTM D648
Electrical
Nominal Value
Unit
Test Method
Arc Resistance (PLC) 5
 
 ASTM D495
UL
Nominal Value
Unit
Test Method
RTI Str
°F
 UL 746
RTI Imp
°F
 UL 746
RTI Elec
°F
 UL 746
Comparative Tracking Index (CTI) (PLC)
 
 UL 746
High Voltage Arc Tracking Rate (HVTR) (PLC)
 
 UL 746
Hot-wire Ignition (HWI) (PLC)
 
 UL 746
High Amp Arc Ignition (HAI) (PLC)
 
 UL 746
Related Terminology
This supplier and product may also be known by these terms: GE Plastics, LNP Engineering Plastics, GE Polymerland

Product names can be difficult to match. You may have searched any one of these terms to find this product: ULTEM* 1110F Resin, ULTEM 1110F Resin, ULTEM* , ULTEM, ULTEM1110FResin, 1110 F Resin, 1110F Resin, 1110F, FResin, 1110FResin, Polyether Imide, PEI, SABIC IP, PolyetherImide, F1110
Features
Features may also be described by the following terms: Good Flow.
Agency Ratings
This plastic material has 4 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): EU (2), FDA (1), NSF (1).
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Drying Time, Maximum
hr
  
Suggested Max Moisture
%
  
Suggested Shot Size
%
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Nozzle Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Back Pressure
psi
  
Screw Speed
rpm
  
Vent Depth
in
  
Notes
1Typical properties: these are not to be construed as specifications.
20.20 in/min
3Type I, 0.20 in/min
40.10 in/min
5Tungsten Electrode
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.